Sears Craftsman 944.601131 страница 7 Скачать руководство пользователя

Страница: 7 / 56

ASSEMBLY

FIG. 2

FIG. 3

HEX BOLT

NEGATIVE
(BLACK)
CABLE

POSITIVE (RED)
CABLE

DISCARD
TERMINAL
PROTECTIVE
CAPS

KEPS
NUT

BATTERY
BOX DOOR

SEAT PAN

•

If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.

•

First connect RED battery cable to positive (+) terminal
with hex bolt and keps nut as shown. Tighten securely.

•

Connect BLACK grounding cable to negative (-) terminal
with remaining hex bolt and keps nut. Tighten securely.

•

Close battery box door.

Open battery box door for:
•

Inspection for secure connections (to tighten hardware).

•

Inspection for corrosion.

•

Testing battery.

•

Jumping (if required).

•

Periodic charging .

TO ROLL TRACTOR OFF SKID (See Opera-
tion section, page 10, for location and func-
tion of controls)

•

Press lift lever plunger and raise attachment lift lever to
its highest position.

•

Release parking brake by depressing clutch/brake pedal.

•

Place gearshift lever in neutral (N) position.

•

Roll tractor forward off skid.

•

Remove banding holding deflector shield up against
tractor.

FIG. 4

NOTE:

You may now roll or drive your tractor off the skid.

Follow the appropriate instruction below to remove the
tractor from the skid.

SEAT PAN

SHOULDER
BOLT

ADJUSTMENT
KNOB

FLAT WASHER

SEAT

INSTALL SEAT (See Fig. 4)

Adjust seat before tightening adjustment knob.
•

Remove adjustment knob and flat washer securing seat
to cardboard packing and set aside for assembly of seat
to tractor.

•

Pivot seat upward and remove from the cardboard
packing. Remove the cardboard packing and discard.

•

Place seat on seat pan so head of shoulder bolt is
positioned over large slotted hole in pan.

•

Push down on seat to engage shoulder bolt in slot and
pull seat towards rear of tractor.

•

Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.

•

Lower seat into operating position and sit on seat.

•

Slide seat until a comfortable position is reached which
allows you to press clutch/brake pedal all the way down.

•

Get off seat without moving its adjusted position.

•

Raise seat and tighten adjustment knob securely.

Содержание Craftsman 944.601131

























































Результаты поиска

Содержание Craftsman 944.601131

Отзывы:

Похожие инструкции для Craftsman 944.601131

Бренды по названию

Популярные бренды

Sears Craftsman 944.601131, Руководство пользователя

Результаты поиска

Содержание Craftsman 944.601131

Отзывы:

Похожие инструкции для Craftsman 944.601131

Бренды по названию

Популярные бренды