Sears 30727 Скачать руководство пользователя

Страница: 40 / 45

| 008 Sears CA Treadmill Service Manual [rev 1.0]

Section Three |

Troubleshooting

Treadmill Troubleshooting

No Motor Movement

Symptom

Possible Cause

Test Procedure

Repair

No Motor Movement
- Upon pressing start,
console responds
normally, keys respond
normally, and elevation
works but no belt
movement.

Inadequate power.

-Check for dedicated
circuit (20 amp is ideal)

and check wall outlet

voltage (120 VAC).
-Make sure machine is
not on extension cord or

surge protector or GFCI.

Reference p4.

If the AC voltage is
missing or incorrect,
check the AC service or
consult an electrician.

Damaged or improper
wiring.

-Verify there are no
pinches or cuts in the
power cord, power wires
motor wires, or console
cable.
-Verify console cable
continuity.
Reference p24.
-Verify the connections
of above wires and
cords.

Replace parts as
needed.

Failed motor control
board (MCB).

-Verify power from
MCB. Reference p19.

Replace MCB.

Failed drive motor.

-Measure voltage output
from motor. Reference
motor, AC Wire Voltage
Check p21.

Replace drive motor.

Failed optic sensor.

-Verify voltage of digital
sensor. Reference p19.

Replace optic sensor.

Содержание 30727














































Результаты поиска

Содержание 30727

Отзывы:

Похожие инструкции для 30727

Бренды по названию

Популярные бренды

Sears 30727, Руководство по обслуживанию

Результаты поиска

Содержание 30727

Отзывы:

Похожие инструкции для 30727

Бренды по названию

Популярные бренды