background image

 

3) RED LED – Indicates there is a problem with one or more of the vehicle's system. A vehicle displaying a red LED is definitely not  

 

ready for an emissions test. the red Led is also an indication that there are dtcs present. the mIL lamp on the vehicle's instrument  

 

panel will be lit. the problem that is causing the red Led to light must be repaired before an emissions test can be performed.

 

     

audio Tone Interpretation

 

The audio tone could be configured according to the I/M Readiness Status. This function is invaluable when working in bright areas  

 

where LED illumination alone is not sufficient. It is recommended to set the audio tone to Beep ON. For detailed setup information,  

 

please refer to Status Beep Set System Setup.

 

note: the following audio tone description only works in Scan tool mode.

 

different audio tone with different Led lights will indicates different I/m readiness Status.

      

 

NOTE: 

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTaNT:

 no liability is accepted for incorrect use of this product.

WaRRaNTy:

 Guarantee is 12 months from purchase date, proof of which will be required for any claim.

Sole uK distributor, Sealey Group.

Kempson Way, Suffolk Business Park,

Bury St. edmunds, Suffolk.

IP32 7Ar

www.sealey.co.uk

[email protected]

01284 757500

01284 703534

Environmental Protection

recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be 

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

WEEE Regulations

dispose of this product at the end of its working life in compliance with the eu directive on 

Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed

of in an environmentally protective way. contact your local solid waste authority for recycling information.

VS8812 | Issue 1 27/02/17

Original Language Version

© Jack Sealey Limited

Page 13

Led Light

Audio tone

Beep Interval

Green Led

Bleep off

Yellow Led

two short Beeps

0.5 Second

red Led

two short Beeps

0.5 Second

Содержание VS8812















Отзывы: