background image

INSTRUCTIONS FOR:

METAL TURNING LATHE

MODEL No:

 

SM27.V2

 

1.1. 

Electrical Safety

  

WARNING!

 It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other 
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A 
Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current 
Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected 
by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer. 

You must

 also read and understand the following instructions concerning electrical safety:

1.1.1. 

The Electricity at Work Act 1989 

requires all portable electrical appliances, if used on business premises, to be tested by a qualified  

 

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. 

The

 

Health & Safety at Work Act 1974 

makes owners of electrical appliances responsible for the safe condition of those appliances  

 

and the safety of the appliance operators. 

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3.  Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.   
 

and use a Portable Appliance Tester.

1.1.4.  Ensure that cables are always protected against short circuit and overload.
1.1.5.  Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none are loose.
1.1.6. 

Important:

 Ensure that the voltage marked on the appliance matches the power supply 

 

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. 

DO NOT

 pull or carry the appliance by the power cable.

1.1.8. 

DO NOT 

pull the plug from the socket by the cable.

1.1.9. 

DO NOT

 use worn or damaged cables, plugs or connectors. Immediately have any faulty item  

 

repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is  damaged, cut the  

 

cable just above the plug and 

dispose of the plug safely. 

 

Fit a new plug according to the following instructions (UK only).

 

a)  Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 

b)  Connect the BROWN live wire to the live terminal ‘L’.

 

c)  Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

d)  After wiring, check that there are no bare wires, that all wires have been correctly   

 

connected, that the cable outer insulation extends beyond the cable restraint and that the  

 

restraint is tight.

 

Double insulated products, which are always marked with this symbol     , are fitted with live (brown)  

 

and neutral (blue) wires only. To rewire, connect the wires as indicated above - 

DO NOT

 connect  

 

either wire to the earth terminal.

1.1.10.  Products which require more than 13Amps are supplied without a plug. In this case you must contact  
 

a qualified electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of an   

 

industrial round pin plug and socket with your electrician.

1.1.11.  If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance   
 

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the  

 

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use   

 

of 2.5mm² section cable.

1.2.    General Safety

 

WARNING!

 

Disconnect the lathe from the mains power and ensure that the chuck or face plate is at a complete standstill before attempting  

 

to change accessories, service or perform any maintenance.

 

Maintain the

 

lathe in good condition (use an authorised service agent).

 

Replace or repair damaged parts. 

Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

Locate the lathe in a suitable area. Ensure that the mounting surface is flat and firm. Keep the area clean and tidy and free from unrelated  

 

materials, and ensure that there is adequate lighting.

 

Keep the lathe clean for best and safest performance. 

 

WARNING! Before each use check that face plate/chuck, cutting tool and tailstock are secure and not worn or damaged. If any part of the  

 

lathe is worn or damaged replace immediately.

Original Language Version

SM27.V2    Issue: 2(L) - 06/03/15

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE THE PRODUCT 

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL 
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 
instructions, and properly maintained, give you years of trouble free performance.

 1.  SAFETY

Refer to

instruction 

manual

Wear eye

protection

RECOMMENDED

 FUSE RATING: 13AMP

 © Jack Sealey Limited

Содержание SM27.V2








Отзывы: