fig.1
KEY
1. Spindle lock
2. On/Off switch
3. Safety button
4. Twin blades
5. Rear handle
6. Locking button for rear handle
7. Auxiliary handle
8. Safety guard
9. Lever for safety guard
10.Wax stick
11.Feeding knob for wax stick
12.Wrench
13.Feed Aperture
2. INTRODUCTION
3. SPECIFICATION
4. OPERATION
Designed for cutting metals, plastics, woods and aluminium materials. Twin blades rotate in opposite directions creating a fast, burr-free, clean
cut whilst minimising kick-back and sparks for a safer operation. Features a controlled lubricating feed direct into blades for maintaining cutting
efficiency and cooling blades. Three position rotating handle with soft grip for added comfort. Die-cast aluminium safety guard. Supplied in
storage case with ten lubricating sticks. Additional lubricating sticks and replacement blade sets available separately - order Model No’s SMT125L
& SMT125B.
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SCT125
BladeSize: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø125mm
Maximum Cutting Depth: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30mm
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 920W
Supply:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
No Load Speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4500rpm
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.25kg
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.96m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.48m/s²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90dB(A)
Affix the auxilliary handle (fig1.7) Select the required rear handle position by pressing the handle locking button (fig.1.6) and turning the
handle appropriately.
4.1. SAWING
WARNING:
Ensure that the power flex is always laid well clear of the saw blades.
4.1.1.
Secure the work to a stable support before attempting to cut .
4.1.2.
Ensure that the workpiece is supported close to the cut and that the cut is closest to you.
4.1.3.
Switch on by depressing the safety button (fig.1.6) and then the on/off switch (fig.1.2)
4.1.4.
Run the saw up to full speed before offering the blades to the work. Failure to do so could result in the blades snatching, leading to a
poor cut and the risk of injury.
4.1.5.
Employ a steady pressure when guiding the saw. Excessive pressure will result in an uneven cut and will reduce the service life of the
blades.
4.1.6.
Always cut in a straight line; any sideways pressure will result in the blades binding. This will cause overheating and premature wear.
4.1.7.
Feed the saw into the work at a steady rate; if the motor slows appreciably, reduce the feed rate. Too slow a feed rate can cause
premature wear.
SCT125 Issue:1 - 13/11/14
Original Language Version
© Jack Sealey Limited
