background image

NOTE:

 It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION:

 For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group, 

Kempson Way, Suffolk Business Park

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

email

Original Language Version

SA26.V3   Issue: 1 - 09/07/12

© Jack Sealey Limited 2012 

Risk of Hand Arm Vibration Injury. 

The SA26.V3 Air Angle Drill 10mm Reversible when operated in accordance with these instruction and tested in accordance 

with BS EN ISO 8662-6:1995 results in the following vibration emission declared in accordance with  BS EN12096:1997. 

Measured vibration emission value: .................... 0.89m/s²  

Uncertainty:  ........................................... 0.36m/s²

These values are suitable for comparison with emission levels of other tools that have been subject to the same test.

This tool may cause hand-arm vibration syndrome if its use is inadequately managed.

Recommended Measures to reduce risk of hand-arm vibration syndrome: 

This item represents a low Hand Arm Vibration 

risk to users. The calculated maximum usage period exceeds 8 hours. We recommend appropriate safety equipment is utilised 

and regular breaks for the operator are employed to reduce any residual risk of fatigue or repetitive strain injury.

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to 

www.sealey.co.uk, email [email protected] or phone 01284 757500.

Содержание SA26.V3






Отзывы: