2. TECHNICAL SPECIFICATION
Maximum Bobbin Height Above Table: . . . . . . . . . . . . . . . . . . . 110mm
Maximum Length of Bobbins: . . . . . . . . . . . . . . . . . . . . . . . . . .140mm
Oscillating Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24mm
Oscillations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24opm
Table Tilt: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-45°
Table Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .370 x 370mm
Work Table Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .475mm
Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1400rpm
Dust Extraction Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50mm
Bobbins Included: . . . . . . . . . . . . . . . .19 x 90, 38 x 140, 50 x 140mm
Bobbins Optional: . . . . . . . . . . . . . . 25 x 90, 44 x 140, 76.2 x 140mm
Motor:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz 370W
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.7kg
3. ASSEMBLY
3.1.
Install Rubber Feet
3.1.1.
The sander comes ready assembled apart from the rubber feet.
3.1.2. Fit the feet to the four mounting points on the underside of the sander and secure with the four
nuts and bolts.
3.2.
Fit Sandpaper to Bobbin
3.2.1. Undo the nut (Fig 1) securing the sandpaper cylinder. Note! It has a left-hand thread.
3.2.2. Remove the nut and withdraw the sandpaper (Fig 2).
3.2.3. Slide the new sandpaper cylinder on and replace the nut. The rubber bobbin expands as you
tighten the nut and grips the sandpaper cylinder.
3.3.
Fit Bobbin to Machine
3.3.1. Lower the bobbin through the hole in the top of the machine.
3.3.2. Locate the bobbin spindle thread into the motor drive spindle.
3.3.3. Using two spanners tighten the chuck (Fig 3) until the bobbin is firmly held in place. Do not
over-tighten.
3.4.
Fit Table Insert
3.4.1 The SM1301 is supplied with two table inserts for each bobbin, one with a round cutout and one
with an oval cutout. For normal sanding with the table flat use the insert with the round cutout.
For sanding with the table at an angle use the insert with an oval cutout.
3.4.2. The table inserts have a small cutout on the edge to enable them to locate with the peg on the
table.
3.4.3. To remove an insert simply push from underneath the table.
3.5.
Check Table Top for Level
3.5.1. The table may be tilted through 45°.
3.5.2. To check the table is set at 0° use a 90° set square between the table top and the bobbin.
3.5.3. If it is not square locate the stop bolt on the underside of the table above the degree plate.
3.5.4. Adjust the stop bolt until the table is at 90° with bobbin and tighten locknut on the stop bolt.
3.5.6. Slacken the screw on the degree pointer and align with the zero mark. Tighten screw.
1.3. LEAD PAINT WARNING!
Paint once contained lead as a traditional ingredient. Contact with the dust from the removal of such paint is toxic and must therefore be
avoided. The following action must be taken before using the sander on a surface that you suspect may contain lead paint.
1. User must determine potential hazard relating to age of paint to be removed (modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the work area.
3. We recommend personal protection by using the following safety items:
a) Paint Spray Respirator (Our ref SSP16EN)
b) PE Coated Hooded Coverall (Our ref SSP266).
c) Latex Gloves (Our ref SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment as in (3) above and thoroughly clean all areas when task is complete. Ensure paint waste is disposed
of, in sealed bags or containers, according to local regulations.
Fig 1
Fig 2
Fig 3
Original Language Version
SM1301 Issue: 2 - 23/03/10
