1.2. MODEL POWERMIG 2500 only,
IS A SINGLE PHASE MACHINE.
IMPORTANT: TO ACHIEVE MAXIMUM OUTPUT THIS MODEL WILL REQUIRE
A 30AMP FUSED SUPPLY. WE RECOMMEND YOU DISCUSS THE INSTALLATION
OF AN INDUSTRIAL ROUND PIN PLUG & SOCKET WITH YOUR ELECTRICIAN.
1.2.1.
To fit a 13Amp plug proceed as follows:
(UK only - see diagram figure 1).
Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the GREEN/YELLOW earth wire to the earth terminal E.
b) Connect the BROWN live wire to live terminal L.
c) Connect the BLUE neutral wire to the neutral terminal N.
After wiring, check there are no bare wires, that all wires have been
correctly connected and that the wire restraint is tight.
1.2.2.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before connection. A cable reel
with an RCD fitted is recommended since any product which is plugged into the cable reel will be protected.
The cross-section of the cable on the cable reel must be suitable for the unit and never lower than the cross-section of the main cable supplied with unit.
INSTRUCTIONS FOR:
Thank you for purchasing a Sealey Welder. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT
:
BEFORE USING THIS PRODUCT, PLEASE READ THE INSTRUCTIONS CAREFULLY. MAKE CAREFUL NOTE OF SAFETY INSTRUCTIONS,
WARNINGS AND CAUTIONS. THIS PRODUCT SHOULD ONLY BE USED FOR ITS INTENDED PURPOSE. FAILURE TO DO SO MAY CAUSE DAMAGE
OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
P O W E R M I G 2 5 0 0 , P O W E R M I G 2 7 5 0 ,
P O W E R M I G 3 5 0 0 , P O W E R M I G 4 5 0 0 .
1. 3. MODELS POWERMIG 2750, 3500 & 4500.
ARE 3 PHASE MACHINES AND MUST HAVE AN APPROPRIATE PLUG FITTED.
p
p
p
WARNING!
ELECTRICAL INSTALLATION OF WELDER TO A 3 PHASE 415VOLT SUPPLY MUST ONLY BE CARRIED OUT BY A QUALIFIED
ELECTRICIAN. Make sure the power supply cable is correctly connected to the Earth.
1.3.1.
This product must be fitted with a 3 phase plug according to diagram figure 2, and will
require a minimum of 16AMPs per phase, (preferably 32AMP) electrical supply.
You must contact a qualified Electrician to ensure an appropriately fused supply is available.
Connect GREEN/YELLOW wire to Earth E
Connect BLUE wire to R1 (or L1) Terminal.
Connect BROWN wire to S2 (L2) Terminal.
Connect the BLACK wire to terminal 3.
When completed, check there are no bare wires, that all wires have been connected correctly and the
cable restraint is tight.
1.3.2.
DO NOT use this product with a standard extension cable. Only use ARMOURED
extension cable.
1.1.
ELECTRICAL SAFETY.
p
p
p
WARNING! It is the users responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and all electrical connections
for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all electrical products. It is
particularly important to use an RCD together with portable products that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a
professional electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must
also read and understand the following instructions
concerning electrical safety.
1.1.1.
The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on a business premises, to be tested by a qualified
Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.1.2.
The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance, and the safety of the
appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2. above and use a Portable
appliance Tester (PAT).
1.1.4.
Ensure that cables are always protected against short circuit and overload.
1.1.5.
Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power connections, to ensure that none are loose.
1.1.6.
Important:
Ensure the voltage marked on the product is the same as the electrical power supply to be used, and check that plugs are fitted with correct capacity fuse.
1.1.7.
DO NOT pull or carry the powered appliance by its power supply lead or output cables.
1.1.8.
DO NOT pull power plugs from sockets by the power cable.
1.1.9.
DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by a qualified Electrician. A U.K. 3 pin plug with ASTA/BS approval is
fitted. In case of damage, cut off and fit a new plug according to the model, (discard old plug safely).
1.1.10. Some products require more than a 13Amp electrical supply. In such a case,
NO
plug will be fitted.
You must
contact a qualified Electrician to ensure a 30 amp fused
supply is available. We recommend you discuss the installation of a industrial round pin plug & socket with your electrician.
1.1.11.
Cable extension reels
. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted is recommended
since any product which is plugged into the cable reel will be protected. The cross-section of the cable on the cable reel must be suitable for the unit and
never lower than the cross-section of the main cable supplied with the unit.
Blue
Neutral
wire
Yellow & Green
Earth wire
wire
restraint
FUSE RATING
IS 13Amp.
Brown
Live
wire
fig 1
fig 2
POWERMIG2500, 2750, 3500, 4500. - (0051) - (1) - 270100
