6. MAINTENANCE
WARNING! Before attempting any maintenance ensure the unit is unplugged
from the mains power supply.
6.1.
Keep the machine clean and dry. Do not use abrasives to clean the unit. Ensure all
external head screws are tight.
6.2.
Clean regularly by blowing a jet of compressed air through side vents to ensure motor ventilation is kept clear.
WARNING!
Wear approved safety eye protection and, if necessary, respiratory protection.
note. The following maintenance must only be carried out by a technically qualified person or an authorised Sealey service agent.
6.3.
Check carbon brushes by removing each side screw (fig.6). Check to see if the brushes are worn or cracked. If so, the brushes must
be replaced to avoid sparking and damage to the armature. Always change brushes as a pair. Use only genuine spare parts as these
are specifically designed for the machine. Failure to do so may be dangerous and will invalidate your warranty.
6.4.
After each 500 hours of use replace the gear head grease to prevent gear wear and possible drive failure.
5. OpERATION
WARNING! Ensure you read, understand and apply the safety instructions in Section 1.
Ensure the power control switch is NOT locked on before plugging into the mains.
5.1.
Hold the polisher firmly with one hand on the handle grip and the other on the side handle. To select the required speed rotate the
speed selector switch (fig.5.2) to the required speed 1 to 6.
Speed Settings: Range from 1000rpm - 3000rpm
5.1.1. To start the polisher press and hold down the safety lock button (fig.5.1) and squeeze the trigger. When releasing the trigger, the
safety lock button will engage, preventing the polisher from being inadvertently started.
WARNING! The high speed settings are intended for sanding. If used for polishing an excessive amount of surface material may
be removed.
Note:
As the rubber support disc is flexible, when sanding it should not be used head on, but at an angle of approximately 10 to 20
degrees.
Contact your Sealey Dealer for details of compound heads and lambs wool
bonnets.
Fig.5
1
2
Fig.6
Fig.7
WARNING!
The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
noTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMpORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
Original Language Version
Original Language Version
WARNING! – Risk of hand Arm Vibration Injury.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
When operated in accordance with these instructions and tested in accordance with the standard below, results in the following vibration
emission declared in accordance with EN 12096:1997
Tested in accordance with:
BS EN ISO 28927-3:2009
Measured vibration emission value (a):
3.402 m/s²
Uncertainty value(k):
1.5 m/s²
These values are suitable for comparison with the vibration emission levels of other tools that have been obtained using the same test
method.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each
tool. Note that the value declared is an average figure from a series of tests according to the applicable standard. The value may differ
depending on a number of variables including but not limited to; the user; the condition of the tool; attachments made to the tool i.e.
sockets, grinding/cutting discs, sanding discs, blades, handles, leader hoses (always recommended as this helps to reduce vibration).
health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures can be
modified to help prevent significant handicap.
personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury by attenuating the vibration
emissions of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain warm and dry and
maintain good blood circulation in fingers etc.
Guidance relating to the management of hand arm vibration can be found on the HSC website www.hse.gov.uk – Hand-arm Vibration at
Work.
Environmental protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to: www.sealey.co.uk,
email: [email protected] or phone: 01284 757500
© Jack Sealey Ltd
MS900PS Issue: 2(SP) - 16/01/13
MS900PS Issue: 2(SP) - 16/01/13
© Jack Sealey Ltd
