3. GENERAL INsTRUCTIONs
WARNING! Ensure the light is disconnected from the mains power supply before attempting any of the following.
3.1.
PORTABLE LIGHTs
Portable lights have a detachable stand. to assemble, remove the locking screw from the stand and push the end of the stand through the housing on
the bottom of the light. Align the internal nut in the stand with the hole in the housing and then secure with the locking screw.
3.2.
TELEsCOPIC sTANDs
Depending on the model, assembly as follows: a) Detachable legs. Insert in the leg holes in the stand base.
b) fitted legs. Push the leg locking catch up and move the leg downward. Let go of the locking catch and
the leg will lock itself into one of the two locking position. repeat for each leg ensuring each leg is
locked at the same angle.
to extend the upright support, loosen the locking collar at the end of each section, raise the inner support to the required height and tighten the locking
collar. fit the light(s) to the top of the stand. for double light models, fix the junction box onto the bolt in the middle at the top of the stand, with one light
each side. check that the electrical cable runs directly down the stand to the floor.
DO NOT
allow the cable to extend across the workshop above floor
level. some models have storage hooks for excess cable.
check that the assembly is secure and that all nuts and bolts are tight (
DO NOT
overtighten). stand light on a suitable, level surface before use.
3.3.
CLAMP LIGHTs
May be supported with the spring clamp, or suspended from the supplied hook attached to the cover securing screw (see illustration on box).
Ensure all angle arm securing bolts are tight before using the light. remember, the light will become very hot in use, allow to cool before repositioning.
3.4.
BULB CHANGING
WARNING! Disconnect the light from the power supply and allow to cool before attempting to touch the unit.
DO NOT touch the new halogen bulb as the natural oil from your fingers will shorten the bulb life. Handle with a dry, clean cloth only.
3.4.1. Loosen the screw on the top of the front cover (fig.4) and undo, allowing the front cover to open. check to ensure that the screw is retained in the front
cover tab (3) by the washer.
3.4.2. remove the old bulb and discard. Hold the new bulb (1) in a clean cloth and insert it (always use the correctly rated bulb).
3.4.3. check that the weather seal is correctly located in the rim (4) and the washer is on the securing screw. close the font cover. seal by tightening the
securing screw.
3.5.
GENERAL
use only original sealey parts for repair or replacement. repairs must only be undertaken by a qualified electrician.
clean the light with a dry, dust-free cloth.
DO NOT
use solvents or abrasives to clean the light.
Avoid touching the glass shield (fig.4.2) as handling may reduce service life and cause the glass to crack. If necessary clean the shield (when cold) with
alcohol and a soft cloth. If the glass is damaged, replace it immediately. use genuine sealey replacement glass.
DO NOT
use other glass and
DO NOT
use the light without the glass shield.
Although weather proof, the light must not be stored wet. should the unit become wet, unplug from mains and wipe dry before storing.
DO NOT
use the light without the weather seal intact.
fig.4
If you use an extension lead
the cable must be fully unwound from the drum
.
the light is weather proof and may be used out doors. Ensure any extensions and plugs are weatherproof.
If using a tripod ensure that the legs are fully extended and are standing on a level, solid surface. Ensure that the cable is safely routed.
Allow power cables to run down the length of the light stand to the floor.
DO NOT
allow power cables to hang from lights above floor level.
If the light uses a clamp to support it during use, ensure that the object to which you clamp it is strong enough.
DANGER! DO NOT direct the light into a person’s eyes. All models have a very intense light output which, if incorrectly used, could cause eye
damage.
DO NOT
touch the light when operating. Allow to cool before touching, light operates at high temperature.
DO NOT
handle halogen bulbs as the natural oil from your fingers will shorten the bulb life. Handle only with a soft dry cloth.
DO NOT
stand on the legs of a telescopic stand, and
DO NOT
hang other items, or tools, from a telescopic stand.
DO NOT
use the light without the front glass shield. Avoid touching the glass shield as handling may reduce its serviceable life and cause the glass to crack.
DO NOT
use the light without the weather seals intact.
DO NOT
use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a safe, dry, childproof area.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
sole UK Distributor, sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
Web
Original Language Version
ML150c, ML300c.V2, ML500X.V2, ML1000D.V2, ML300/110,
ML500/110VX.V2, ML1000D/110V.V2, cL150
Issue: 2 - 02/11/09
