2. intrODuctiOn
Generation series ratchet wrench featuring contoured soft grip handle and 360° directional exhaust. the kit includes a selection of Walldrive®
impact sockets, extension bars and driver bit, contained in a carry-case.
3. specificatiOn
model no....................................GsA20....................................GsA21
drive...........................................3/8”sq.....................................1/2”sq
maximum torque.............45lb.ft (61nm).........................45lb.ft (61nm)
free speed................................150rpm...................................150rpm
Air consumption............................5cfm.......................................5cfm
operating Pressure ......................90psi......................................90psi
Air inlet size.............................1/4”BsP..................................1/4”BsP
length.......................................280mm...................................280mm
Weight..........................................1.2kg......................................1.2kg
noise Power/Pressure.............99/88dB..................................99/88dB
Vibration/uncertainty..........1.7/0.85m/s
2
...........................1.7/0.85m/s
2
contents GsA20Kit:
Air ratchet Wrench; model no. GsA20 - 3/8”sq drive, Walldrive® impact sockets; 9, 10, 11, 13, 14, 17, 19mm, duometric® coverage; 7/16”,
3/4”, 75mm extension Bar, 75mm Bit Holder, driver Bits; slotted - 5.5mm, Phillips - #2, #3, universal Joint, oil container
contents GsA21Kit:
Air ratchet Wrench; model no. GsA21 - 1/2”sq drive, Walldrive® impact sockets; 9, 10, 11, 13, 14, 17, 19mm, duometric®
coverage; 7/16”, 3/4”, 75mm extension Bar, 75mm Bit Holder, driver Bits; slotted - 5.5mm, Phillips - #2, #3, universal Joint, oil container
4. OperatiOn
4.1.
air supply
warninG!
ensure the air supply is clean and does not exceed 90 psi while operating the die wrench. too high an air pressure and unclean
air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1. recommended hook-up procedure is shown in fig.1.
ensure wrench air valve (or trigger) is in “off” position before connecting to the air supply.
4.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
4.1.3. drain the air tank daily. Water in the air line will damage the wrench.
4.1.4. clean air inlet filter weekly.
4.1.5. line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should be 1/4”
i.d. and fittings must have the same inside dimensions.
4.1.6. Keep hose away from heat, oil and sharp edges. check hose for wear, and make certain that all connections are secure.
4.2.
couplings
.
Vibration may cause failure if a quick change coupling is connected directly to the wrench. to overcome this, connect a leader hose to
the grinder. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. figs.1 & 2.
4.3.
Operating
warninG!
ensure you read, understand and apply safety instructions before use.
4.3.1.
Only use impact sockets which are specifically designed for use with a ratchet wrench.
4.3.2. connect the wrench to the air hose as indicated above.
4.3.3. Place the socket over the subject nut and depress the trigger to operate the wrench.
4.3.4. to change wrench direction turn the switch on the head of the wrench (see fig.3).
8
DO nOt
use any additional force upon the wrench in order to remove a nut.
8
DO nOt
allow wrench to free run for an extended period of time as this will shorten its life.
4.3.5.
The direction of the air flow from the exhaust holes in the central sleeve can be altered by rotating the whole sleeve to a suitable position.
the sleeve can be rotated continuously through 360
°
(see fig.3).
fig.1
fig.2
GsA20,GsA20Kit,GsA21,GsA21Kit - V2 | issue 1 15/03/17
Original Language Version
© Jack sealey limited
