MODE 2 10A TYPE 2 TO UK 3-PIN PLUG
PORTABLE EV CHARGER - 5M CABLE
MODEL NO:
EVPC2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information:
it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
` correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N
’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING!
The charger
must not
be used in conjunction with an extension cord, timer or other accessory between wall outlet and
charger.
WARNING!
Modern vehicles contain extensive electronic systems. You are required to check with the vehicle manufacturer, for any
specific instructions regarding the use of this type of equipment on each vehicle. No liability will be accepted for damage / injury,
where this product is not used in accordance with all instructions.
8
DO NOT
expose equipment to rain or moisture.
8
DO NOT
use if the cables, sockets or unit are damaged.
8
DO NOT
start using the equipment if the plugs, cables etc. are dirty or wet. Wipe clean with a dry cloth if necessary
8
DO NOT
place the equipment in the car or a confined place when charging.
8
DO NOT
expose the equipment to high temperatures.
8
DO NOT
clean the equipment with chemical cleaners.
8
DO NOT
use whilst under the influence of drugs, alcohol or intoxicating medication.
8
DO NOT
pull or carry the unit by its cables.
8
DO NOT
use this equipment to perform a task for which it is not designed.
1.2.1.
The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
person, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2.
The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3.
Ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply.
1.2.4.
Ensure that cables are always protected against short circuit and overload.
1.2.5.
Regularly inspect power supply, leads, plugs for wear and damage and power connections to ensure that none is loose.
1.2.6.
Check product voltage is the same as power supply to be used
1.2.7.
Store the unit in a safe dry environment out of the reach of children.
1.2.8.
This product does not contain user-serviceable parts, please do not try to repair or maintain the product on your own.
Replacement fuse
rating: 13A
E
VPC2 Issue 1 11/06/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Electrical shock
hazard
Wear eye
protection
Keep in dry area
protect from rain
Warning
