InstructIons for:
CAR POLISHER 230mm 110W/230V
MoDEL no:
ER230P.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.2. GENERAL SAFETY
WARNING!
Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this polisher.
familiarise yourself with the application, limitations and potential hazards of the polisher.
WARNING!
Disconnect from the mains power and ensure that the pad is at a complete
standstill before changing accessories, servicing or performing any maintenance.
Maintain the polisher in good condition (use an authorised service agent).
replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
WARNING!
Keep all guards and holding screws in place, tight and in good working order.
check regularly for damaged parts. A guard or any other part that is damaged must be
repaired/replaced before the polisher is next used.
use the polisher in a suitable work area and keep the area clean and tidy and free from
unrelated materials. Ensure that there is adequate lighting.
Keep the polisher clean for the best and safest performance.
Before each use, check all attachments for condition. If worn or damaged, replace immediately.
Ensure that there are no flammable materials near the work area.
WARNING!
Wear approved safety eye protection, ear defenders and, if dust is generated,
respiratory protection.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
remove ties, watches, rings, ill fitting clothing and other loose jewellery, contain and/or tie back long hair.
Keep children and unauthorised persons away from the work area.
Avoid unintentional starting.
DO NOT
use the polisher for any purpose other than that for which it is designed.
DO NOT
operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the panel.
DO NOT
use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
1.1.
ELECTRICAL SAFETY
WARNING!
It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also recommend that a residual current
Device (rcD) is used. It is particularly important to use an rcD with portable products that are plugged into a supply which is not protected
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current Device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety:
1.1.1. the
Electricity at Work Act 198
9 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and
dispose of the plug safely
.
fit a new plug according to the following instructions (uK only):
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b)
Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer
insulation extends beyond the cable restraint and that the restraint is tight.
Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above -
DO NOT
connect either wire to the earth terminal.
1.1.10. Products which require more than 13amp are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcD fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1. SAFETY INSTRUCTIONS
A FUSE RATED AT 5AMP IS
RECOMMENDED
Original Language Version
Er230P.V2 Issue no.2(sP) 25/02/14
© Jack sealey Limited
