3. SPECIFICATION
DO NOT
get the polisher wet or use in damp or wet locations or areas where there is condensation.
DO NOT
allow untrained persons to operate the polisher.
DO NOT
operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
DO NOT
leave the polisher operating unattended.
DO NOT
carry the polisher with your finger on the power switch.
DO NOT
pull the cord from the power supply.
use a qualified person to maintain the polisher.
When not in use, unplug from the mains power supply and store with the foam pad facing upwards, in a safe, dry, childproof area.
2. INTRODUCTION
random orbital polisher with Ø230mm 5 ply foam pad and two polishing bonnets. smooth operation provides even buffing/polishing with no
hot spots. Impact resistant ABs housing with 360º grip. supplied with 4mtr cable and Bs approved plug.
4. OPERATION
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1.
WARNING! Excess pressure can cause damage to paintwork and will put the polisher motor under strain. Polishers returned
with burnt out motors will be rejected as a warranty claim. Normally the weight of the polisher is sufficient.
WARNING! DO NOT use the polisher with abrasive or rubbing compounds.
WARNING! DO NOT immerse the polisher in water.
4.1.
stretch the bonnet over the pad, ensure that it is centrally positioned and stretched out smoothly.
4.2.
Before each use, check that the bonnet is clean and free of abrasive particles and is undamaged and that the pad rotates freely.
4.3.
Apply a small amount of polish/wax evenly over the surface of the bonnet.
DO NOT
apply polish directly to the vehicle surface.
4.4.
Hold the polisher firmly by the handles and place the polishing face onto the panel to be polished.
4.5.
start the polisher by sliding the red on/off switch to the on position, ensuring that the pad is still in contact with the vehicle panel.
4.6.
Move the polisher with broad sweeping strokes over the surface in a criss cross pattern.
DO NOT
apply pressure to the polisher when
in use. Work in logical areas and re-apply the polish/wax at intervals during the polish application process.
DO NOT
allow the foam pad
to become saturated with polish/wax as this will make polishing more difficult and will also reduce pad life.
4.7.
switch off the polisher before lifting it from the panel, when polish application is completed.
4.8.
In less accessible areas, polish/wax should be applied by hand, removing the bonnet from the pad.
4.9.
remove the application bonnet and replace it with the polishing bonnet.
4.10.
Buff the polish/wax in the same order it was applied.
DO NOT
put pressure on the polisher but allow its weight and action to do the job.
4.11.
Badly oxidised paint may require several applications.
DO NOT
use abrasive compounds.
4.12.
If the polish/wax is difficult to buff, too much has been applied. this may also cause the bonnet to come off the pad.
Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . Er230P.V2
Input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110W
speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3300rpm
Vibration (load): . . . . . . . . . . . . . . . . . . . . . . . .13.48m/s²
uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.39m/s²
Pad size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø230mm
cable Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4mtr
replacement Backing Pad: . . . . . . . . . . . . . Er230P.BP
replacement Bonnet terry cloth: . . . . . . . . Er230P.tB
replacement Bonnet synthetic Wool: . . . . . Er230P.WB
noise Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99dB
noise Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . 88dB
5. MAINTENANCE
5.1.
Always store the polisher with the foam pad facing upwards, so it does not become compressed or distorted.
5.2.
remove the bonnet when not in use to allow the foam pad to dry out.
5.3.
clean the bonnet regularly by hand washing with soap and water, and allow it to dry thoroughly. Washing the bonnet is sufficient -
DO NOT
immerse the foam pad in water.
5.4.
to remove the foam pad, proceed as follows:
5.4.1. remove the bonnet and undo the two small cross head screws in the centre of the pad. Prise out the plastic centre cover.
5.4.2. Insert a rod (screwdriver or similar) into one of the two slots in the back of the pad and to the right of the central shaft, rotate the pad
clockwise until the rod contacts with the counter-weight.
5.4.3. undo the centre screw (not the cross head screw). the screw has a left hand thread, turn it clockwise to undo it.
5.4.4. refit the pad reversing the procedure above.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park
,
Bury st. Edmunds, suffolk,
IP32 7Ar
www.sealey.co.uk
W e b
Original Language Version
Er230P.V2 Issue no.2(sP) 25/02/14
© Jack sealey Limited
Parts support is available for this product. to obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or phone 01284 757500.
Environmental Protection.
recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the Eu Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. contact your local solid waste
authority for recycling information.
