Battery:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8V
speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 mm/min
charge time: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1hour
Accessories:. . . . . . . . . . . . . . . . . . . . . . . . . . . . Extra Battery
Battery Model no: . . . . . . . . . . . . . . . . . . . . . . . cPc48VrBP
Weight Inc. Battery: . . . . . . . . . . . . . . . . . . . . . . 2.1kg
no. of cartridges per hour:. . . . . . . . . . . . . . . . . 35 cartridges (310ml silicone at room temperature. Approx).
2. inTRODuCTiOn & SPECiFiCaTiOn
Ideal for dispensing 310ml cartridges and sausage packs. Anti-drip feature with variable rewind and variable speed control allows pin-point control of
caulking bead. superb gun for dispensing all types of caulking - particularly suitable for windscreen repair applications.
fig.2
fig.1
3. OPERaTing inSTRuCTiOnS
note:
When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several subsequent charges
may also take a little longer than when the battery pack reaches its optimum performance. remove battery pack from case and charge as below:
3.1.
CHaRging THE BaTTERY PaCk
3.1.1. Plug the Ac charger into the supply wall outlet.
3.1.2. to remove the battery pack from gun, depress the two side release clips and withdraw battery from the gun handle.
WaRning! Do not touch metal terminals.
3.1.3. the battery pack and charger have the positive (+) and negative (-) terminals marked. Align the correct terminals and insert the battery into
the charger.
Note: The battery pack is so designed that it will only enter the charger unit the correct way
. When placed in the charger, a very slight downward
pressure will seat the pack firmly onto the terminals. the red LED will light when the battery is inserted to indicate power supply is
connected, and battery is charging.
3.1.4. the charging will take approximately 1 hour from a fully discharged state. When fully charged the LED on the charger will light green to
indicate a trickle charge.
3.1.5. After removing the battery, disconnect the charger from the mains supply and store in the carry case.
WaRning! never leave the battery unattended whilst charging due to the potential fire hazard.
Note: If two batteries are to be charged in succession allow the charger to cool between uses.
3.2.
SauSagE Bag aPPLiCaTiOn.
3.2.1. Ensure plastic head (fig.1) is fitted. If not, unscrew and
remove the compound holder, loosen the M8 screw (fig.2) fit
the plastic head (fig.3) and tighten the M8 screw.
3.2.2. cut a hole in one end of the sausage bag (fig.4).
3.2.3. remove the front cap from the compound holder. fit the
nozzle and cut the tip of to suit your requirements (fig.5).
3.2.4. Insert the sausage bag into the front of the compound holder.
screw the front cap and nozzle on.
3.2.5. Push the rear knob forward gently advancing the rack until it
comes into contact with the sausage pack. the sausage pack
is now loaded and ready to use.
Do not operate the charger if it has been dropped, or has received a sharp knock, or is damaged. take the charger to an authorised
agent for repair or obtain a replacement.
Do not dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
Do not insert foreign objects or material into the hole reserved for the battery pack.
Original Language Version
cPc48Vr Issue: 2 - 26/10/09
