correct fuse.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damage cables, plugs or connectors. Immediately have any faulty item repaired or
replaced by a qualified electrician.When an ASTA/BS approved UK 3 pin plug is damaged, cut the cable
just above the plug and dispose of the plug safely. Ensure that the double insulated charger is correctly
connected via a three-pin plug, as follows:
a)
Connect the Brown live wire to live terminal ‘L’.
b)
Connect the Blue neutral wire to the neutral terminal ‘n’.
c)
After wiring, check that there are no bare wires, that all wires have been correctly connected,
that the cable outer insulation extends past the cable clamp and that the clamp is tight. note that the
earth pin ‘E’ remains unconnected.
1.3.7. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to
be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we
recommend the use of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.
1.4. BATTERY chARGER SAFETY INSTRucTIONS
WARNING! DO NOT
attempt to charge any battery other than that supplied for the wrench. other types of batteries may explode!
9
All mains electrical supply safety features must be followed as described in 1.3 above.
9
Disconnect the charger from the mains supply when not in use.
8
DO NOT
charge battery if room temperature is below 10°C (50°F) or above 40°C (104°F).
8
DO NOT
expose the charger to damp or wet conditions.
8
DO NOT
pull or carry the charger by the power lead.
8
DO NOT
operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take the charger to an authorised
agent for repair or obtain a replacement.
8
DO NOT
dismantle the charger as this may cause damage and/or personal injury and will invalidate the warranty.
8
DO NOT
insert foreign objects or material into the hole reserved for the battery pack.
8
DO NOT
recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow the
8
unit to cool for 15 minutes before charging the next pack.
8
DO NOT
attempt to connect two chargers together.
9
Store the charger in the same manner as the battery pack in 1.2.
2.
i
INTRODucTION
Powerful, compact and suitable for removing the most stubborn wheel nuts in the workshop or on roadside with no compressor or mains source
required. Featuring a variable speed switch for added control. Produces torque of up to 680nm (500lb.ft). Forward and reverse control integrated
into housing for ease of use. Suitable for workshop, bodyshop and tyre shop applications without hazardous trailing cables. Powered by a 26V 4Ah
Lithium battery which retains its charge over long periods of time, so always ready to use. Supplied with a 90 minute mains charger.
3.
i
SPEcIFIcATION
4. BATTERY
4.1. chARGING ThE BATTERY PAcK.
4.1.1.
Remove the battery pack from the wrench, by depressing the two side release clips (fig.1.4).
WARNING!
DO NOT
touch metal terminals.
4.1.2. Place wrench in carry case and remove the battery charger.
4.1.3. Connect the charger to the mains electricity supply. The green LED will flash continuously.
4.1.4. The battery pack has the positive (+) and negative (-) terminals marked. Align the battery with its docking point and insert it into slot.
NOTE: The battery pack is designed so that it will only enter the charger unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack firmly into the power terminals.
4.1.5. When inserted correctly, the chargers red charge light will show a steady illuminated aspect whilst the battery is charging.
4.1.6. When the charge is complete the green LED will show a steady illuminated aspect. The battery pack is now ready for use.
NOTE:
When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several subsequent
charges may also take a little longer than when the battery pack reaches its optimum performance. Afterwards, normal charging time is
approximately 90 minutes.
4.1.7. After removing the battery by depressing the release clips (fig.1.4), disconnect the charger from the mains supply and store in the carry
case as described in section 1.2.
IMPORTANT WARRANTY INFORMATION:
The battery pack fitted to this cordless tool is considered to be a consumable item and its ability to accept charge will reduce over
time. We will guarantee it against mechanical and electrical defect for a period of one year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will
not replace the battery pack even if it is less than one year old. Remove battery pack from case and charge as above:
Original Language Version
© Jack Sealey Limited
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cP2612
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26V 4Ah Li-ion
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2"Sq.
no load speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2000rpm
Impact Rate: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2600bpm
Maximum Torque:. . . . . . . . . . . . . . . . . . . . . . . .680nm(500lb.ft)
Replacement Battery:. . . . . . . . . . . . . . . . . . . . . . . . . . .CP26BP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3kg
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
cP2634
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26V 4Ah Li-ion
Drive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3/4"Sq.
no load speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2000rpm
Impact Rate: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-2600bpm
Maximum Torque:. . . . . . . . . . . . . . . . . . . . . . . .816nm(600lb.ft)
Replacement Battery:. . . . . . . . . . . . . . . . . . . . . . . . . . .CP26BP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3kg
CP2612, CP2634 Issue1 - 06/12/17
REcOMMENDED
FuSE RATING: 5AMP
