4.5.
Fit Battery
4.6.
Slide battery pack down until button clicks. Press button in and pull upwards to remove
WARNING!
Take care to NOT press the On/off button whilst fitting/removing the battery pack.
4.7.
Switching on and off
WARNING:
Always wear safety goggles, an adequate dust mask, hearing protection and suitable gloves, when working with this
tool.
WARNING:
never switch the sander on when the base is in contact with the workpiece or any other surface, as this might cause
the operator to lose control over the machine and lead to serious injury.
4.7.1.
Fit the battery.
4.7.2.
Push the right hand (when viewed from the front) on/off Switch to toggle through the 3 speeds.
4.7.3.
To switch the sander off press the left hand (when viewed from the front) switch.
WARNING:
Always wait until the machine has stopped vibrating completely before putting it down. Always disconnect the battery
after use.
4.8.
Sanding
4.8.1.
Fit the dust collection bag before use.
4.8.2.
move the sander in a circular motion over the workpiece surface, applying an even, moderate pressure until you reach the desired
surface finish
WARNING:
excessive pressure does not lead to a faster removal of material; it will, however, lead to premature wear of the
sanding disc, and may cause damage to the machine.
4.8.3.
If there are still scratches on your workpiece after sanding, refer to ‘Selecting the right grade of sanding disc’.
5. MAINTENANCE
WARNING:
Always disconnect the battery before carrying out any inspection, maintenance or cleaning.
5.1.
General inspection
5.1.1.
Regularly check that all the fixing screws are tight.
5.1.2.
Repairs should be carried out by an authorised service centre.
5.2.
Emptying the dust extraction bag
WARNING:
Always switch off and disconnect from the battery before detaching the dust extraction system.
WARNING:
Always wear respiratory protection, eye protection and gloves when emptying the dust Bag.
5.2.1.
note: For optimum dust removal, empty the dust Bag when it is no more than half full.
5.2.2.
To empty the bag pull the bag assembly from the extraction pipe, hold it upright and twist the cap anticlockwise to remove the cap.
5.2.3.
Dispose of the waste.
note: If the sanding dust contains harmful substances, such as particles from old paint, varnish, surface coatings etc., always
dispose of according to local laws and regulations.
5.2.4.
note: Always clean the tool THoRoUGHlY when switching from sanding wood to sanding metal and vice versa.
5.3.
Cleaning
WARNING:
Always wear protective equipment including eye protection and gloves when cleaning this tool.
5.3.1.
Keep your tool clean at all times. dirt and dust will cause internal parts to wear quickly, and shorten the device’s service life.
5.3.2.
Clean the body of your machine with a soft brush, or dry cloth.
5.3.3.
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent on a damp cloth is recommended.
5.3.4.
Water must never come into contact with the tool ensure the tool is thoroughly dry before using it.
5.3.5.
If available, use clean, dry, compressed air to blow through the ventilation holes (where applicable).
5.4.
Lubrication
5.4.1.
Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant.
5.5.
Brushes
5.5.1.
over time the carbon brushes inside the motor may become worn
5.5.2.
excessively worn brushes may cause loss of power, intermittent failure, or visible sparking.
5.5.3.
If you suspect that the brushes may be worn, have them replaced at an authorised service centre.
5.6.
Storage
5.6.1.
Store this tool carefully in a secure, dry place out of the reach of children.
the HSC website
Original Language Version
© Jack Sealey limited
CP20VoS | Issue 1 10/04/18
