1.3.
BATTERY SAFETY PRECAUTIONS
WARNING!
Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
9
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
8
DO NOT
Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT
Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT
Expose to temperatures above 40°C (104°F).
9
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
8
DO NOT
attempt recharging the battery by means of an engine generator or a dC power source.
WARNING!
Dispose of spent batteries correctly as they contain Lithium-ion.
DANGER
!
DO NOT
attempt to disassemble the
battery. For safety and environmental reasons
DO NOT
discard in domestic waste or by burning.
ONLY
discard or recycle
according to local authority regulations.
WARNING!
DO NOT
allow a leaking battery to contact your person.
1.4.
GENERAL SAFETY
9
disconnect the polisher from the battery unit before changing accessories, servicing or performing any maintenance.
9
maintain the polisher and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
ensure the polisher is switched off before installing the battery pack.
9
Keep the polisher and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the polisher e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
ensure battery pack is correctly inserted into the polisher handle and securely in place before attempting to switch on polisher.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep children and unauthorised persons away from the working area.
9
Keep polisher and charger in the case and store in a safe, dry childproof area where the temperature will not exceed 104°F (40°C).
8
DO NOT
use the polisher where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the polisher.
8
DO NOT
operate the polisher if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the polisher operating unattended.
8
DO NOT
carry the polisher with your finger on the power switch.
8
DO NOT
use the polisher for a task it is not designed to perform.
8
DO NOT
operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the polisher, battery or battery charger wet or use in damp or wet locations.
2. INTRODUCTION
Powered by 18V 4Ah Lithium-ion battery. Digital display and variable speed control from 500-2800rpm. Features a slide button on/
off switch allowing for a smooth comfortable main handle grip. Spindle lock for fast and easy pad changes. double injection composite
housing with rubber grip for added comfort. Supplied with Ø150mm backing pad and side handle. Includes mains charger. Covered by
Sealey three year warranty*.
3. SPECIFICATION
Model No.: .............................................................CP18VRP
Battery (CP18VBP)
.........................................
18V 4Ah Li-ion
F
ree speed ......................................................
500 - 3000rpm
Pad size ..................................................................
Ø150mm
Thread size .........................................................
M14 x 2mm
noise power .............................................................
85dB(A)
noise pressure ..........................................................
74dB(A)
B
acking pad .................................................
PTC/150VA/M14
Charging base ........................................................
CP18V/11
B
attery ...................................................................
CP18VBP
4. OPERATION
WARNING:
Remove battery before fitting / removing pads or maintenance is carried out.
NOTE:
When new, the batteries may have been shipped in a low charge state. Fully charge the batteries before using your tool.
4.1.
Ensure that you have read, understood and comply with all the safety instructions in Section 1.
4.2.
BATTERY CHARGER
4.2.1.
To remove the battery from the equipment, depress the spring loaded tab on the front of the battery pack. Remove the battery pack by
sliding it out.
DO NOT
touch the metal battery terminals.
4.2.2.
The battery is designed to fit into the charger one way only. Insert the battery fully and firmly to seat the battery into the charging base.
4.2.3.
Take the base charger and plug it into the mains, switch on the power and the led on the charger will illuminate.
4.2.4.
When the battery is on charge the red LED on the charger will illuminate.
4.2.5.
When the green LED on the charger illuminates permanently the battery is fully charged.
4.2.6.
The battery has 3 LED charge level indicators that show full or partial charges levels.
4.2.7.
The battery charge state can be determined, when not being charged, by depressing the tab next to the led display on the battery.
4.2.8.
Remove the battery from the charger. Switch off and remove the plug from the mains.
Original Language Version
© Jack Sealey limited
C
P18VRP Issue 1 28/10/19
