9
once vehicle is supported, ensure that the vehicle and stands are stable before starting work. ensure that it is not possible for the vehicle
to move before commencing any work.
9
inspect stands before each use.
do not
use if they show signs of damage.
do not
use if it is suspected that they have been
overloaded.
9
Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible person is aware of
the work about to be undertaken.
9
replace any labels on the axle stand should they become unreadable. this applies in particular to any warning or operation instruction
labels. if replacement labels are required, contact your sealey stockist.
8
do not
use axle stands on the highway, or anywhere else if it is deemed to be unsafe.
8
do not
push or twist the vehicle/load whilst it is supported on stands.
8
do not
mix components between stands. use only as supplied.
8
do not
allow children or animals in the vicinity of a vehicle supported on axle stands.
8
do not
leave a vehicle on axle stands in an area that could be considered a hazard to others or property.
9
follow StepS 1, 2, and 3 to correctly place vehicle / load onto axle StandS.
2. introduction
jack
single piece hydraulic unit with heavy chassis design. integral American cog-type release mechanism and long two piece handle. Heavy duty
castors and large saddle design ease positioning under vehicle. fitted with safety overload valve and pump through valve to prevent handle
locking at maximum ram extension. supplied with a pair of ratchet type axle stands, 3 tonne (3000kg) capacity per stand (6 tonne (6,000kg) per
pair). ideal for loaded vans up to 3.5tonne GVW.
axle StandS
ratchet type axle stands, with cast iron support posts. features angled teeth in posts, which prevent accidental release of load - the more
weight applied, the tighter the post is locked. sold in pairs.
3. Specification
jack
Model no: ................................................................. 3010cx
minimum saddle height: ............................................. 133mm
maximum saddle height: ............................................ 515mm
maximum saddle height: ............................................ 154mm
length: ....................................................................... 661mm
Weight: ........................................................................ 36.8kg
axle StandS
Model no: ................................................................. vS1003
capacity each: ......................................... 3 tonnes (3,000kg)
capacity per pair: ..................................... 6 tonnes (6,000kg)
minimum height: ......................................................... 287mm
maximum height: ........................................................ 427mm
4. operation - jack
4.1.
Before first use.
4.1.1.
Assemble the handle by lining up the holes in the two-piece handle and fasten with the assembly screw.
4.1.2.
loosen location bolt at the back of the handle base. insert the jack handle and tighten the bolt.
4.1.3.
Before using jack, purge the hydraulic unit in order to eliminate any air in the system. open the valve by turning the handle
anti-clockwise (fig.1), and pumping 8 or 9 times. When complete, close the release valve by turning the handle fully clockwise (fig.1).
4.1.4.
Place a few drops of hydraulic jack oil onto the pump piston and pump the handle several times to distribute the oil. thoroughly
lubricate all moving parts.
General jacking.
warninG!
Before lifting ensure section 1 safety instructions are read and understood.
4.1.5.
Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which the jack is to stand is level and solid (not
tarmacadam) and use chocks under wheels of vehicle.
4.1.6.
Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
4.2.
jacking the vehicle.
4.2.1.
turn the handle clockwise to close the release valve (fig.1)
and commence pumping handle up and down until the jack saddle reaches
the vehicle jacking point. check the jacking point is centrally located on the saddle and continue to pump the handle to raise the vehicle.
Original Language Version
© Jack sealey limited
3010cX issue:4 - 27/09/16