Seagull RANS S-20 RAVEN-20cc Скачать руководство пользователя страница 2

Страница: 2 / 40

RANS S-20 RAVEN 20cc

Instruction Manual.

Thank you for choosing the

RANS S-20 RAVEN 20cc

ARF by

SG MODELS

. The

RANS S-20

RAVEN 20cc

was designed with the intermediate/advanced sport flyer in mind. It is a semi scale

airplane which is easy to fly and quick to assemble. The airframe is conventionally built using

balsa, plywood to make it stronger than the average ARF, yet the design allows the aeroplane to be

kept light. You will find that most of the work has been done for you already. The motor mount has

been fitted and the hinges are pre-installed. Flying the

RANS S-20 RAVEN 20cc

is simply a joy.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual throughly before starting assembly of your

RANS S-20 RAVEN 20cc

. Use the parts

listing below to indentify all parts.

INTRODUCTION.

WARNING.

KIT CONTENTS

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & REPONSIBILITY.

If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C

supplier and join your local R/C model Flying Club. R/C Model Flying Clubs offer a variety

of training procedures designed to help the new pilot on his way to successful R/C flight.

They will also be able to advise on any insurance and safety regulations that may apply.

Содержание RANS S-20 RAVEN-20cc









































Результаты поиска

Содержание RANS S-20 RAVEN-20cc

Отзывы:

Бренды по названию

Популярные бренды

Seagull RANS S-20 RAVEN-20cc, Инструкция по сборке

Результаты поиска

Содержание RANS S-20 RAVEN-20cc

Отзывы:

Бренды по названию

Популярные бренды