manualshive.com logo in svg

Seagull MAP-X2, Руководство пользователя

Поделиться
Скачать
Seagull MAP-X2 Скачать руководство пользователя страница 3

© 2020 Seagull UAV All Rights Reserved.   3 

GENERAL INFORMATION 

 

*** Please read this manual thoroughly before connecting and configuring Seagull #MAP-X2 *** 

 
Seagull #MAP-X2 is a precision camera trigger controller and logger. #MAP-X2 uses your cameras´ hotshoe/event pin for feedback 
and GNSS data to log exact coordinates of when the photo was captured, resulting in a 1:1 ratio between coordinates and photos. 
#MAP-X2 can receive GNSS data via Seagull UAVs´ GNSS receiver products or other GNSS receivers capable of providing necessary 
messages, that are recognized by #MAP-X2 for data logging.

 

 
NOTE:

 #MAP-X2 can also log GNSS data without a SYNC event feedback. 

 

 

#MAP-X2 features: 

•

 

High data rate sampling 

–

 

4Hz MB, 5Hz RTK, 10Hz RAW, 10Hz GNSS 

•

 

Various trigger modes 

–

 SST, ACT, PWM, BUTTON, TIMELAPSE 

•

 

Trigger and Log 

–

 with or without SYNC feedback 

•

 

Easy geotagging 

–

 Pix4D, EXIF 

•

 

IMU compatible 

–

 improves ORTOPHOTO and 3D Model processing 

•

 

GNSS receiver messages supported 

–

 UBX-NAV-PVT / UBX-RXM-RAWX + UBX-RXM-SFRBX 

 
 
 
 

 

 

Содержание MAP-X2












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды