background image

www.seagullmodels.com

23

 

 

2) Check every bolt and every glue joint

in the 

PERCIVAL MEWGULL 

to ensure that

everything is tight and well bonded.

  

 

E) Check the throttle.  Moving the throttle

stick forward should open the carburetor bar-
rel.  If it does not, flip the servo reversing switch
on your transmitter to change the direction.

 

 

F) From behind the airplane, look at the

aileron on the right wing half.  Move the aileron
stick to the right.  The right aileron should move
up and the other aileron should move down.  If
it does not, flip the servo reversing switch on
your transmitter to change the direction.

PREFLIGHT CHECK.

 

  

  

1) Completely charge your transmitter

and receiver batteries before your first day of
flying.

 

6) Check to ensure the control surfaces

are moving the proper amount for both low
and high rate settings.

 

  

  

8) Properly balance the propeller.  An out

of balance propeller will cause excessive vi-
bration which could lead to engine and/or air-
frame failure.

 

7) Check the receiver antenna.  It should

be fully extended and not coiled up inside the
fuselage.

 

  

  

5) If your radio transmitter is equipped

with dual rate switches double check that they
are on the low rate setting for your first few
flights.

  

3) Double check the balance of the air-

plane.  Do this with the fuel tank empty.

 

  

  

4) Check the control surfaces.  All should

move in the correct direction and not bind in
any way.

FOR USA MARKET ONLY

LY.

As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself
and others or result in damage to the product or the property of others.
Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable
battery packs, etc.) that you use.
This model is controlled by a radio signal that is subject to interference from many sources outside your control.
This interference can cause momentary loss of control so it is necessary to always keep a safe distance in all
directions around your model, as this margin will help to avoid
collisions or injury.
• Always operate your model in an open area away from cars, traffic or people.
• Avoid operating your model in the street where injury or damage can occur.
• Never operate the model out into the street or populated areas for any reason.
• Never operate your model with low transmitter batteries.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable
battery packs, etc.) that you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and
protected for this purpose.

Safety,Precautions and Warnings

Warranty Period:

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”)
will be free from defects in materials and workmanship at the date of purchase by the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT
AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER.  This warranty
covers only those Products purchased from an authorized Horizon dealer. Third party transactions are not covered
by this warranty. Proof of purchase is required for warranty claims. Further, Horizon reserves the right to change or
modify this warranty without notice and disclaims all other warranties, express or implied.

(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
 (c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii)
replace, any Product determined by Horizon to be defective. In the event of a defect, these are the Purchaser’s
exclusive remedies. Horizon reserves the right to inspect any and all equipment involved in a warranty claim. Repair
or replacement decisions are at the sole discretion of Horizon. This warranty does not cover cosmetic damage or
damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part

We wish you many safe and enjoyable
flights with your 

 

PERCIVAL MEWGULL.

Содержание PERCIVAL MEW GULL

























Отзывы: