manualshive.com logo in svg

Seagull Models NIEUPORT 28 REPLICA, Инструкция по сборке

Поделиться
Скачать
Seagull Models NIEUPORT 28 REPLICA Скачать руководство пользователя страница 31

31

INSTALLATION PILOT AND

WINDSHIELD. 

1) Locate items necessary to install pilot

and windshield.

2) A scale pilot is included with this ARF.

Th Pilot included fis well in the cockpit.

(or you can order others scale pilot fiures 

made by SG Models. Thy are available at 

SG Models distributors.)..

If you are going to install a pilot fiure, 

please use a sanding bar to sand the base

of the fiure so that it is flt.

29

.

1

.

Epoxy. 

2

.

3

.

3) Position the pilot fiure on the cockpit 

flor as shown. Use epoxy to glue the base 

of the pilot fiure, please see pictures as 

shown.

3) Position the pilot fiure on the cockpit 

flor as shown. Use epoxy to glue the base 

of the pilot fiure, please see pictures as 

shown.

4) Position the windshield onto the fuse-

lage. Trace around the windshield onto

the fuselage using a felt-tipped pen. Cut

and remove the covering from between

the lines drawn, and glue the windshield

to the fuselage using epoxy or a special

canopy glue.

4

.

Содержание NIEUPORT 28 REPLICA














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды