manualshive.com logo in svg

Seagull Models DECATHLON ARTF, Инструкция по сборке

Поделиться
Скачать
Seagull Models DECATHLON ARTF Скачать руководство пользователя страница 9

www.seagullmodels.com

9

 

  

  

1)  The blind nuts for securing the landing

gear are already mounted inside the fuselage.

 

  

  

2)  Using the hardware provided, mount

the main landing gear to the fuselage.

INSTALLING THE MAIN LANDING GEAR.

M4 x 10mm.

M4 x 20mm.

M4 x 10mm.

   

  

  

3)  A drop of C/A glue on the wheel collar

screws will help keep them from coming lose
during operation.

  Repeat the process for the other wheel.

Landing Gear.

wheel Pant.

Locker glue.

MOUNTING THE ENGINE.

 3)  Remove the engine. Using an drill bit,

drill the mounting holes through the engine
mount at the four locations marked.

 

1)  Place your engine onto the engine

mount. Adjust  the engine is centered of the
edges of the engine case.

 

2)  When you are satisfied with the align-

ment, mark the locations of the engine
mounting.

Alumium Spar.

Alumium Spar.

140mm
.

Alumium Spar.

Содержание DECATHLON ARTF























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды