manualshive.com logo in svg

Seagull Models DECATHLON ARTF, Инструкция по сборке

Поделиться
Скачать
Seagull Models DECATHLON ARTF Скачать руководство пользователя страница 8

DECATHLON _ 

CODE SEA 86

.

  

                                                                

Instruction Manual

8

Fuel pick-up tube.

Fuel fill tube.

Vent tube.

Blow through one of the lines to ensure
the fuel lines have not become kinked in-

side the fuel tank compartment.  Air should
flow through easily.

FUEL TANK INSTALLATION.

You should mark which tube is the vent
and which is the fuel pickup when you

attach fuel tubing to the tubes in the stopper.
Once the tank is installed inside the fuselage,
it may be difficult to determine which is which.

C/A glue attched.

Fuel tank.

Plastic tape.

Balsa Block.

  

 2)  Follow diagram below for wheel pant

installation:

wheel collar.

wheel.

Axle.

Washer.

M3.

wheel Pant.

wheel.

M3.

M3.

wheel collar.

nut.

Axle.

Washer.

  

 1)  Assemble and mounting the wheel pants

as shown in the following  pictures.

WHEEL AND WHEEL PANTS

INSTALLATION.

M3.

12mm.

5mm.

Содержание DECATHLON ARTF























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды