manualshive.com logo in svg

Seagull Models DECATHLON ARTF, Инструкция по сборке

Поделиться
Скачать
Seagull Models DECATHLON ARTF Скачать руководство пользователя страница 1

Made in Vietnam.

“Graphics and specifications may change without notice”.

Kit features.

•

Ready-made—minimal assembly & finishing required.

•

Ready-covered covering.

•

Photo-illustrated step-by-step Assembly Manual.

     Specifications

Wing span-------------------------------------- 70.9 in------------------------------ 180cm.
Wing area-------------------------------------- 837 sq.in------------------------54 sq.dm.
Approximate flying weight------------------7.5-8.8 lbs---------------------3.4-4.0kg.
Length------------------------------------------ 47.6in------------------------------- 121cm.
Recommended engine size-------------- .75cu.in-------------------------- 2-stroke.
                                                                  .91cu.in--------------------------4-stroke.

Radio  System  required 4 channels  with 6 servos
Flying skill level  Intermediate/advanced.

ASSEMBLY MANUAL

MS: 86

Содержание DECATHLON ARTF























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды