Seagate SKYHAWK SURVEILLANCE AI 5 E Series Скачать руководство пользователя страница 19

Страница: 19 / 28

Seagate SkyHawk AI Serial ATA Product Manual, Rev. C

3.4

Drive mounting

Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes.
See

Figure 4

for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:

• Allow a minimum clearance of 0.030 in (0.76mm) around the entire perimeter of the drive for cooling.

• Use only 6-32 UNC mounting screws.

• The screws should be inserted no more than 0.140 in (3.56mm) into the bottom or side mounting holes.

• Do not overtighten the mounting screws (maximum torque: 6 in-lb).

3.4.1

Mechanical specifications

Refer to

Figure 4

for detailed mounting configuration dimensions. See

Section 3.4

, “Drive mounting.”

Figure 4.

Mounting configuration dimensions 5-disk models

Figure 5.

Weight:

10TB models

1.587 lb

720g

Note

These dimensions conform to the Small Form Factor Standard documented in
SFF-8301 and SFF-8323, found at

www.sffcommittee.org

Note

The image is for mechanical dimension reference only and may not represent the actual drive.

2X 1.750±.010

3X 3.750±.010

2 2X 1.432±.020

3X .125±.010

2X 1.625±.020

2X 3.000±.010

2 .814±.020

CL OF DRIVE

6X 6-32 UNC-2B

.169 .010 x 90

3 MIN THREAD DEPTH

.14 MAX FASTENER PENETRATION

MOUNTING HOLES

MAX TORQUE: 6 IN-LBF

CL OF CONN

3X .250±.010

BOTH SIDES

1.122±.020

1.638±.010

4.000±.010

6X 6-32 UNC-2B

.160 .010 x 90

3 MIN THREAD DEPTH

.14 MAX FASTENER PENETRATION

MOUNTING HOLES BOTH SIDES

MAX TORQUE: 6 IN-LBF

1.028 MAX

[26.10MM]

2 .138±.015

2.000

CL OF DRIVE

TEMPERATURE

CHECKPOINT

60 C MAX

4.000±.010

5.787 MAX

147.00 MM

Содержание SKYHAWK SURVEILLANCE AI 5 E Series





























Результаты поиска

Содержание SKYHAWK SURVEILLANCE AI 5 E Series

Отзывы:

Похожие инструкции для SKYHAWK SURVEILLANCE AI 5 E Series

Бренды по названию

Популярные бренды

Seagate SKYHAWK SURVEILLANCE AI 5 E Series, Руководство по эксплуатации продукта

Результаты поиска

Содержание SKYHAWK SURVEILLANCE AI 5 E Series

Отзывы:

Похожие инструкции для SKYHAWK SURVEILLANCE AI 5 E Series

Бренды по названию

Популярные бренды