SeaDoo 2002 GTX 4-TEC Скачать руководство пользователя | Manualshive

Страница: 82 / 100

background image

80

TROUBLESHOOTING

The following chart is provided to help in diagnosing the probable source of simple
troubles. You may be able to solve many of these problems rather quickly, but
others may require the skills of a mechanical technician. In such cases, consult
an authorized Sea-Doo dealer for servicing.

NOTE:

For the definition of abbreviations used here, refer to ABBREVIATIONS

USED IN THIS MANUAL section below.

Monitoring Beeper Coded Signals

NOTE:

When the beeper sounds, also look the message displayed on the infor-

mation center to obtain more details on the problem. Refer to INFORMATION
CENTER.

CODED SIGNALS

POSSIBLE CAUSE

REMEDY

2 short beeps
(while installing safety
lanyard on post).

• Confirms safety lanyard signal

operation.

Engine can be started.

1 long beep
(while installing safety
lanyard on watercraft post or
when pressing engine
start/stop button).

• Bad DESS system connection.

Reinstall safety lanyard cap cor-
rectly over post.

• Wrong safety lanyard.

Use a safety lanyard that has
been programmed for the water-
craft.

• Defective safety lanyard.

Use another programmed safety
lanyard.

• Dried salt water in safety

lanyard cap.

Clean safety lanyard cap to re-
move salt water.

• Improper operation of engine

ECU or defective wiring
harness.

Refer to an authorized Sea-Doo
dealer.

1 short beep followed by
1 long beep.

• ECU has been inadvertently set

to onboard diagnostic mode.

Remove and reinstall safety lan-
yard.

2 very short beeps every
3 seconds interval for
25 minutes.

• Safety lanyard has been left on

its post without starting engine
or after engine was stopped.

To prevent battery discharge, re-
move the safety lanyard from its
post.

A 2 seconds beep every
minute interval.

• High pressure in oil separator

tank.

Refer to an authorized Sea-Doo
dealer.

• Low fuel level.

Refer to an authorized Sea-Doo
dealer.

• Fuel tank level sensor or circuit

malfunction.

Refer to an authorized Sea-Doo
dealer.

smo2002-003_a.book Page 80 Friday, October 12, 2001 2:04 PM

«
...
80
81
82
83
84
...
»

Содержание 2002 GTX 4-TEC





































































































Отзывы:

Нет отзывов

Похожие инструкции для 2002 GTX 4-TEC

Бренд: O'Day Страницы: 4

Бренд: Lifetime Страницы: 16

Бренд: Grand Soleil Страницы: 103

Бренд: LaserPerformance Страницы: 16

Бренд: LaserPerformance Страницы: 21

Бренд: Baja Страницы: 84

Бренд: Scarab Страницы: 182

Бренд: Mercury Страницы: 123

Бренд: Mercury Страницы: 522

Бренд: Valiant Страницы: 51

14' Square Stern

Бренд: WaterQuest Страницы: 8

Бренд: Jeanneau Страницы: 100

Бренд: Quicksilver Страницы: 45

Бренд: Zodiac Страницы: 63

Бренд: Zodiac Страницы: 24

GP1200R WaveRunner 2001

Бренд: Yamaha Страницы: 126

Бренд: Zodiac Страницы: 67

Бренд: Brunswick Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды