SEA SLIDE DG R2F Скачать руководство пользователя страница 14

Страница: 14 / 32

WARNING:

Make sure that the gate performs the following cycle for all types of self-learning:

CLOSE - OPEN - CLOSE

; otherwise see

REVERSE MOTOR

function

International registered trademark n. 2.777.971

SELF-LEARNING

It is possible to choose between 3 self-learning ways according to the features of the installation:

AUTOMATIC SELF-LEARNIG:

A - LIMIT-SWITCH
B - ENCODER

MANUAL SELF-LEARNING

C - IMPULSES

SEA

SET

SEA

SET

PROGRAM-

MING

AUTOMATIC SELF-LEARNING

A) WITH LIMIT-SWITCHES

SEA

SET

- -

Limit Switch

opening motor 1

Limit Switch

closing motor 1

WHEN NOT ENGAGED (-)

segment is ON

SEA

SET

WHEN ALL LIMIT SWITCHES

ARE ENGAGED

the

segment are in OFF

SELF-LEARNING starts AUTOMATICALLY and the gate
will perform the following cycle: CLOSE - OPEN - CLOSE (*)

SEA

SET

WHEN SINGLE LIMIT SWITCH

IS ENGAGED

the

segment is in OFF

SEA

SET

SEA

SET

PROGRAM-

MING

If Limit-switches are connected, the automatic self-learning starts in LIMIT-SWITCH mode by default.

Before starting, make sure (through the test menu below), that all limit-switches are engaged

INPUT TEST LIMIT-SWITCHES

: test

each

limit-switch by activation before self-learning.

The segment on display shall disappear when each limit-switch is activated

With Limit-switches engaged follow the instruction below:

B) WITH ENCODER

If Encoder is connected, it is necessary its activation on menu-32 ENCODER by following istructions:

SEA

SET

SEA

SET

ENCODER

Then adjust the sensitivity on obstacle on menu-33 OPENING SENSITIVITY MOTOR 1

SEA

SET

OPENING

SENSITIVITY

SELF-LEARNING starts AUTOMATICALLY and the gate
will perform the following cycle: CLOSE - OPEN - CLOSE

SEA

SET

SEA

SET

PROGRAM-

MING

After Encoder activation and sensitivity adjusting go on menu-9 PROGRAMMING to start the
automatic self-learning:

(*)

If the motor starts in opening, switch off the power and then switch it ON again, select

on the display and through the and put it ON or, if you have the JOLLY 3

programmer, activate the

MOTOR EXCHANGE FUNCTION

* REVERSE MOTOR FUNCTION

SEA

SET

REVERSE

MOTOR

DOWN

Содержание SLIDE DG R2F

































Результаты поиска

Содержание SLIDE DG R2F

Отзывы:

Бренды по названию

Популярные бренды

SEA SLIDE DG R2F, Руководство пользователя

Результаты поиска

Содержание SLIDE DG R2F

Отзывы:

Бренды по названию

Популярные бренды