Sea Tel DAC-03 Скачать руководство пользователя страница 61

Страница: 61 / 80

DAC-03 Tracking Antenna ControllerDAC-03 w/SCPC Receiver Technical Specifications

8-3

8.7.3.2.

SW1 Local Band Select Output

Control local (BDE) band select switch(s) or tone generator(s).

Connections

1 screw terminal connection (SW1)

Control Level:

Low Band = OPEN circuit
High Band = SHORT to ground
Controlled by MODE – TRACKING – Band Selection.

Current sink of 0.5 amps

max

8.7.3.3.

SW2 Blockage / TX Mute Output

Blockage output to Dual Antenna Arbitrator coax switch panel OR TX Mute output to
Satellite Modem for RF radiation hazard and/or FCC compliance.

Connections

1 screw terminal connection (SW2)

Control Level:

Not Blocked or Not mispointed = OPEN circuit*
Blocked or mispointed = SHORT to ground *

Current sink of 0.5 amps

max

*The logic level output can be reversed by adding 16 to the SYSTEM TYPE parameter.

8.7.4.

NMEA Interface

This interface allows up to two simultaneous external GPS or NMEA 0183 compliant Heading inputs
and an echoed GPS (GPGGA) output.

Connections

4 Screw terminal connections (RX+ / RX- input and TX+/ TX-
output)

8.8.

Environmental Conditions

The following requirements apply to equipment installed in weather protected locations.

Temperature

0 to 40 degrees C

Humidity

Up to 100% @ 40 degrees C, Non-condensing

Содержание DAC-03

















































































Результаты поиска

Содержание DAC-03

Отзывы:

Похожие инструкции для DAC-03

Бренды по названию

Популярные бренды

Sea Tel DAC-03, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DAC-03

Отзывы:

Похожие инструкции для DAC-03

Бренды по названию

Популярные бренды