Sea Eagle FishSkiff FSK16 Скачать руководство пользователя страница 12

Страница: 12 / 20

FishSkiff |

ASSEMBLY & INFLATION: OPTIONAL ITEMS

Motor and Battery

(OPTIONAL)

Clamp electric motor (or

up to a 6hp gas motor)

to motor mount before

mounting battery.

Secure battery or gas tank

by running the strap with

buckle over the battery/

tank and through the

D-rings. Strap stretches

when wet, check strap

frequently.

Bow Mount Trolling

Motor (OPTIONAL)

Motormount Hardware

Watersnake has posted

instructions for attaching

Quick Release Bracket

motor on YouTube. The

Sea Eagle bow mount

board is predrilled for the

Quick Release. Quick

Release is not required but

additional holes will need

to be drilled.

Included:

Board Block

4 - M6 x 40 mm socket

head screws

8 - ½” x ¼” flat washers

4 - locking nuts

Motor Bracket

6 - M6 x 35 mm socket

head screws

12 - ½” x ¼” flat washers

6 - locking nuts

Attach Quick Release

adapter block to

aluminum board using

M6 x 40 mm (1 ½”) socket

head screws, washers and

locking nuts. The sides

are tapered, install so that

block and base can slide

together.

Tools needed:

Phillips Head screwdriver, 10 mm

wrench and 5 mm hex wrench.

Attach Quick Release base

to motor following the

video instructions (

Quick

Release Bracket

Locking clip must be on the

left side when

looking at the motor

upside down.

Caution:

Not too

tight! Screwhead will pull

through nylon base.

Near valves in bow (front) are

four D-rings (two on each side

of boat) that hold the

aluminum board to the boat.

Insert large washer through

each bolt. Insert each bolt

through a D-ring so it stands

upward.

Board Attachment Hardware

4 ¼ - 20 x 1¼” Philips Head

Screws

4 5/16 x 1¼” Flat Washer

4 3-Arm Knobs

Place board over the bolts

on one side of boat and work

bolts through the holes.

Start threading knobs onto the

bolts but do not tighten until

bolts are worked though the

holes on the other end of the

board.

Place motor over Quick

Release plate and insert

locking bar. Locking bar

must engage the clip.

Follow manufacturer’s

instructions for deploying

and stowing the motor. For

Watersnake, see the next

page of this manual.

Содержание FishSkiff FSK16





















Результаты поиска

Содержание FishSkiff FSK16

Отзывы:

Похожие инструкции для FishSkiff FSK16

Бренды по названию

Популярные бренды

Sea Eagle FishSkiff FSK16, Инструкция и руководство пользователя

Результаты поиска

Содержание FishSkiff FSK16

Отзывы:

Похожие инструкции для FishSkiff FSK16

Бренды по названию

Популярные бренды