Sea-doo LRV 5688 Скачать руководство пользователя страница 52

Страница: 52 / 71

Deck Drains

Remove any obstruction from deck
drains and scupper valve.

Vacuum Bailer Pick-Ups

They are located each side of the drive
shaft tunnel.

Two pick-ups use a low pressure area
in the jet pump to siphon the water out
of the bilge when the engine is operat-
ing.

Inspect each pick-up screen for ob-
structions, clean as necessary.

TYPICAL

1. Vacuum bailer pick-ups

Fuses

Locate MPEM under seat inside en-
gine compartment of craft.

Remove fuse cover from the MPEM.

TYPICAL

1. MPEM
2. Fuse cover

Use the tabs of the fuse cover to re-
move and reinstall fuses.

1. Fuse cover
2. Fuse tabs

If a fuse is burnt, replace by one of the
same rating.

CAUTION:

Do not use a higher rated

fuse as this can cause severe dam-
age. If a fuse is regularly burnt, refer
to an authorized Sea-Doo dealer.

General Inspection and
Cleaning

Inspection

Check engine compartment for any
damage and fuel/oil injection systems
for leaks. Ensure all hose clamps are
properly secured and no hose is
cracked, kinked or presenting any oth-
er damage.

Inspect muffler, battery, fuel tank and
oil reservoir fastening devices. Visually
check electrical connections for corro-
sion and tightness.

Inspect hull and jet pump water intake
grate for damage. Replace or have
damaged parts repaired.

F01L7RY

F11H01Y



WARNING

If any gasoline leak and/or odor
are present, do not start the en-
gine. Have the craft serviced by
an authorized Sea-Doo dealer.

F06H1TY

smo2000-001b.fm Page 50 Tuesday, May 4, 1999 1:20 PM

www.SeaDooManuals.net

Содержание LRV 5688






































































Результаты поиска

Содержание LRV 5688

Отзывы:

Похожие инструкции для LRV 5688

Бренды по названию

Популярные бренды

Sea-doo LRV 5688, Руководство оператора

Результаты поиска

Содержание LRV 5688

Отзывы:

Похожие инструкции для LRV 5688

Бренды по названию

Популярные бренды