Sea-doo 295100679 Скачать руководство пользователя страница 13

Страница: 13 / 16

3/9/2017

einstructiondetails

http://instructions.brp.com/content/instructionsheet/en_CA/einstructiondetails.html#articleNo=kA0a0000000l0rxCAA&lang=en_CA&title=SEADOO%20KIT… 13/16

TYPICAL

1. BLACK () cable first
2. RED (+) cable last

2. Lift and push top of electrical component support to unlock it from battery holder. Move support
aside to make room.

TYPICAL TOP VIEW

1. Electrical component support

1. Lower receptacle
2. Upper retaining tab

All Models WITHOUT rear access panels

Route wiring harness [P5] from fuse box to depth finder along main wiring harness. Secure it using
locking ties [P8] every 400  mm (16 in) along the way.

NOTICE

Keep wire harness away from sharp edges and moving, rotating or hot parts.

Regroup the wire excess near to the battery and secure with locking ties [P8].

All Models WITH rear access panels

Regroup the wire excess near to the battery and secure with locking ties [P8].

Содержание 295100679

















Результаты поиска

Содержание 295100679

Отзывы:

Бренды по названию

Популярные бренды

Sea-doo 295100679, Руководство пользователя

Результаты поиска

Содержание 295100679

Отзывы:

Бренды по названию

Популярные бренды