Sea Breeze SHE12H4ZIGB Скачать руководство пользователя страница 6

Страница: 6 / 36

950-0203-revK - 6 - March 1, 2016

System Configuration Options

SMZ42H46ZOGX (2 to 5 indoor units)
Note:

1. Do not mismatch or connect to an outdoor unit other than the designed matched system.

2. This system

must

be used with a minimum of

two indoor units

(evaporators).

Indoor Models Available:

Indoor Unit Type

Catalog Number

Outline

Remark

Wall-mounted Indoor Unit

SHE9H4ZIGX
SHE12H4ZIGX
SHE18H4ZIGX

Wall-mounted Indoor Unit

SHE9H4ZIGB
SHE12H4ZIGB
SHE18H4ZIGB
SHE24H4ZIGB

Console Indoor Unit

SMZC9H4ZIGX
SMZC12H4ZIGX
SMZC18H4ZIGX

For  the  detail  information  about
connecting,  please  refer  to  the
specific  manual  included  with
each indoor unit.

Cassette Indoor Unit

SMZCA12H4ZIGX
SMZCA18H4ZIGX
SMZCA24H4ZIGX

Floor / Ceiling Indoor Unit

SMZFC9H4ZIGX
SMZFC12H4ZIGX
SMZFC18H4ZIGX
SMZFC24H4ZIGX

Ducted Indoor Unit

SMZD9H4ZIGX
SMZD12H4ZIGX
SMZD18H4ZIGX
SMZD21H4ZIGX
SMZD24H4ZIGX

2 INDOOR UNITS

3 INDOOR UNITS

4 INDOOR UNITS

5 INDOOR UNITS

9K + 9K

9K + 12K
9K + 18K

12K + 12K
12K + 18K
18K + 18K
12K + 21K
12K + 24K
18K + 21K
18K + 24K
21K + 21K
21K + 24K

9K + 9K + 9K

9K + 9K + 12K
9K + 9K + 18K

9K + 12K + 12K
9K + 12K + 18K
9K + 18K + 18K

12K + 12K + 12K
12K + 12K + 18K
12K + 18K + 18K

9K + 9K + 21K
9K + 9K + 24K

9K + 18K + 21K
9K + 12K + 21K
9K + 12K + 24K

12K + 12K + 21K

9K + 9K + 9K + 9K

9K + 9K + 9K + 12K
9K + 9K + 9K + 18K

9K + 9K + 12K + 12K
9K + 9K + 12K + 18K

9K + 12K + 12K + 12K

9K + 9K + 9K + 9K +9K

The system matches below are not recommended if all indoor units may require simultaneous continuous duty at full efficiency.

24K + 24K

18K + 18K + 18K

9K + 18K + 24K
9K + 21K + 21K
9K + 21K + 24K

12K + 18K + 21K
12K + 18K + 24K
12K + 21K + 21K
12K + 12K + 24K

9K + 9K + 18K + 18K

9K + 12K + 12K + 18K
9K + 12K + 12K + 21K

12K + 12K + 12K + 18K

9K + 9K + 9K + 24K

9K + 9K + 12K + 21K
9K + 9K + 12K + 24K

12K + 12K + 12K + 12K

9K + 9K + 9K + 21K

9K + 9K + 9K + 9K + 18K

9K + 9K + 9K + 12K + 12K

9K+ 9K + 12K + 12K + 12K

9K + 9K + 9K + 9K + 12K

Содержание SHE12H4ZIGB





































Результаты поиска

Содержание SHE12H4ZIGB

Отзывы:

Похожие инструкции для SHE12H4ZIGB

Бренды по названию

Популярные бренды

Sea Breeze SHE12H4ZIGB, Руководство по установке

Результаты поиска

Содержание SHE12H4ZIGB

Отзывы:

Похожие инструкции для SHE12H4ZIGB

Бренды по названию

Популярные бренды