background image

950-0203-revK                                                                                     - 26 -                                                                March 1, 2016 

 
 

Technical Specifications for CASSETTE Indoor Units 

 

 

Model Of Indoor Unit 

SMZCA12H4ZIGX 

SMZCA18H4ZIGX 

SMZCA24H4ZIGX 

 

Product Code 

243-6004-E 

243-6005-E 

243-6006-E 

Performance 

& Electrical  

Rated Voltage 

208-230V AC / 1 PH 

208-230V AC / 1 PH 

208-230V AC / 1 PH 

Control 

Remote (standard) or 

Wall (optional) 

Remote (standard) or 

Wall (optional) 

Remote (standard) or 

Wall (optional) 

Setting Range 

61°F to 86°F 

61°F to 86°F 

61°F to 86°F 

  Cooling Capacity (BTU/H) 

12000 

14400 

22800 

Heating Capacity (BTU/H) 

13000 

16000 

27400 

Wire Size / No. of Conductors 

4C- 14 AWG 

(Recommended) 

4C- 14 AWG 

(Recommended) 

4C- 14 AWG 

(Recommended) 

Indoor Air Circulation (CFM)                                  

(High Fan Speed) 

353 

353 

694 

Dehumidifying Volume(pts/h) 

2.96 

3.8 

5.28 

FAN Motor 

Fan Motor Speed (RPM)                                                         

(SH / H / M / L / SL ) 

845 / 700 / 530 / 600 / 515 

845 / 700 / 530 / 600 / 515 

620 / 570 / 520 / 280  

Output of Fan Motor (W) 

11 

11 

50 

Fan Motor Capacitor (ufd) 

Fan Motor RLA ( A) 

0.23 

0.23 

0.43 

Fan Type 

Centrifugal 

Centrifugal 

Centrifugal 

Diameter-Height (in) 

11.14 

– 5.83 

11.14 

– 5.83 

17.72 

– 4.41 

Evaporator 

Evaporator 

Aluminum fin - Inner 

Grooved copper tube 

Aluminum fin - Inner 

Grooved copper tube 

Aluminum fin - Inner 

Grooved copper tube 

Pipe Diameter (in) 

0.375 

0.375 

0.28 

Row-Fin Gap (in) 

2-0.06 

2-0.06 

3-0.05 

Coil length(L) x height(H) x coil 

width(W) (in) 

37.64 x 8.0 x 1.5 

37.64 x 8.0 x 1.5 

80.35 x 6.75 x 1.18 

Design Data 

Swing Motor Model                                         

(for horizontal louver) 

MP35EA 

MP35EA 

MP35EA 

Fuse(A) 

3.15 

3.15 

3.15 

High Pressure (PSI) 

550 

550 

550 

Low Pressure (PSI) 

240 

240 

240 

Auto Restart 

Yes 

Yes 

Yes 

Condensate Pump 

Yes 

Yes 

Yes 

Condensate Pump lift (ft) 

2.3 

2.3 

3.6 

Anti-Mildew Protection 

Yes 

Yes 

Yes 

Sound Pressure Level dB(A)                         

(High Fan Speed) 

46 

46 

39 

Sound Power Level dB(A)                       

(High Fan Speed) 

56 

56 

49 

Flare Liquid line 

1/4"  

1/4"  

 3/8" 

Flare Suction line 

3/8" 

1/2" 

5/8"  

Dimensions 

& Weight 

Dimensions of Unit                  

(W / D / H)  (approx in) 

22.4 / 22.4 / 9.1 

22.4 / 22.4 / 9.1 

33.1 / 33.1 / 9.45 

Dimension of Package            

(W / D / H)   (approx in) 

33.5 / 28.8 / 12.8 

33.5 / 28.8 / 12.8 

37.9 / 37.9 / 12.8 

Net / Gross Weight (lb) 

39.7 / 50.7 

39.7 / 50.7 

61.7 / 77.2 

Dimensions of Panel               

(W / D / H)   (approx in) 

25.6 / 25.6 / 2.0 

25.6 / 25.6 / 2.0 

37.4 / 37.4 / 2.36 

Dimension of  Panel Package 

(W / D / H) (approx in) 

28.9 / 26.5 / 4.6 

28.9 / 26.5 / 4.6 

41.1 / 40.5 / 5.12 

Net / Gross Weight of Panel (lb) 

5.5 / 8.1 

5.5 / 8.1 

14 / 22 

 
 
 

Содержание SHE12H4ZIGB





































Отзывы: