中文
EN
D
C6 SE SETUP
21
20
C6 SE
SETUP
The C6 SE extension subwoofer can be seamlessly combined with a C6 column speaker system. This
combination provides extended low frequency energy and simply enables C6 to have more bass and
to play louder. Follow the steps outlined below to connect a C6 SE subwoofer to a C6 column system.
If you use two C6 systems to build a stereo setup, add the second C6 SE subwoofer to the second C6
column system in the same way.
1
Place the C6 SE subwoofer at your
desired location and put the C6 subwoofer
on top of it. (see placement section)
2
Set the DSP mode of C6 SE extension
subwoofer to
PSSC IN
.
3
Use an XLR cable and connect the
TO C6 SE
output socket on the C6's
mixer to the
LINE IN
socket at the back
panel of C6 SE.
4
Plug in the powerCON
®
cable into the
POWER IN
socket on each units' rear side
panel and connect both cables to the mains
outlet.
5
Place both column modules according
to the instruction provided in the C6 column
system manual to the corresponding
connector on top of C6.
6
Connect your audio source/s to the
C6 mixer.
7
Turn the
POWER SWITCH
of C6 on first
and of C6 SE extension subwoofer second.
The
ON LED
on each unit should indicate a
constant green light.
Turn down the respective level when you plug in or unplug any audio signal cable.
Always turn down the MAIN LEVEL before powering on or powering off C6 column system.
This helps to prevent sudden loud sound exposure and possible hearing damages.
SPECIFICATIONS
TECHNICAL SPECIFICATIONS
ACOUSTICAL
Frequency range (-3 dB)
1
50 Hz - 250 Hz
Coverage angles (-6 dB) [H x V]
Omnidirectional
Maximum Peak SPL
2
126 dB
System type
1-way, self-powered
Crossover frequency
250 Hz (C6 extension); 80 Hz - 180 Hz
4
th
order low pass (standalone mode)
Transducers
2x 10" woofer with 2.5" voice coil
Enclosure type
Bass reflex
AMPLIFICATION
Type
Class-D with SMPS
Output power
3
800 W
Protection
Short circuit, Overheating, Overcurrent, Limiter
Indicators
Power on, Signal, Limit, Protect
Connectors
Line In: 1x XLR combo jack, balanced
Line Out: 1x XLR, balanced
Power connector: powerCON
®
20A
Wiring
Pin layout XLR: Pin 2: ; Pin 3: Signal-; Pin 1: Shield
Pin layout TRS: Tip: ; Ring: Signal-; Shaft: Shield
Pin layout powerCON
®
: Pin N: Neutral;
Pin L: Conductor; Pin E: Earth, Ground
Operating voltage range
100 – 240 VAC, 50/60 Hz
Input sensitivity
0 dBu
DSP
48 kHz/24 bit with extended dynamics
Processing latency: 1.1 ms
Processing
Crossover, Limiter, EQ, Level
User controls
Power: On/Off switch; 1x Subwoofer Level; 1x Lowpass Crossover; 1x Mode Switch (PSSC/Line In);
1x Sub Phase Switch 0°/180°
MECHANICAL
Product dimensions
[H x W x D] (Including rigging)
347 x 750 x 532 mm
Net weight
35.5 kg
Packaging dimensions
[H x W x D]
433 x 830 x 615 mm
Total weight
38 kg
Cabinet
Subwoofer: Plywood
Cabinet finishing
Black polyurea coating
Grille
Powder coated perforated steel
Hardware
2 side handles embedded in cabinet;
Rubber feet; recesses for C6 column system stacking
ACCESSORIES
C6 TD
Transport Dolly for C6 or C6 SE
C6 FC
Flightcase for C6 or C6 SE
1
Half space, 1 W / 1m
2
Calculated Max. Peak SPL = Sensi 10log
10
(output power)
3
According to EIA-426B Standard
Figure 10.
Connect C-Line C6 SE subwoofer to C6 column system.
XLR
powerCON
®
100-240 V~ 50-60 Hz
Max. 2000 W
