SDM TRIAX 100, Инструкция по эксплуатации

Страница: 5 / 12

8 9
The various features of your watch are grouped into 8 different modes.
CYCLE TO A MODE
Press MODE/NEXT repeatedly until desired mode appears.
TIME
Time and calendar information for two time zones.
RUN
View pace, speed and distance, set and view zone
training information and calibrate the speed
sensor.
GRAPH
View graphic display of speed.
CHRON (CHRONOGRAPH)
Measure and record lap and split times.
DATA
Recall lap, split and speed/distance.
TIMER
5-segment countdown timer.
ALARM
Features 2 alarms.
DEMO mode provides a brief demonstration of each mode. While in TIME
mode, press START/LAP and STOP simultaneously. You will hear the sound
demonstration. The watch will cycle through the modes, briefly
demonstrating the functions of each. Press any button to exit DEMO mode.
OPERATING INSTRUCTIONS
CYCLE TO
A MODE
Press MODE/NEXT to select
desired mode.
T
X
E
N
/
E
D
O
M
S
T
O
P
S
T
A
R
T
/
L
A
P
T
I
X
E
/
T
S
U
J
D
A
S
T
A
R
T
/L
A
P
A
D
JU
S
T
/ E
XIT
M
O
D
E
/
N
E
X
T
ST
O
P
H20 RESIST 1
00M
MODES
The SDM Triax 100 watch provides accurate speed and
distance information for most runners. However, if you
have a non-standard gait, like a pronating stride, you can
calibrate the speed sensor by running a known distance
and adjusting its display accordingly.
1. Go to a running track of any length. A 400
meter track is recommended as the most
common, but a longer track is better.
2. Press MODE/NEXT to select RUN mode.
3. Press and hold ADJUST/EXIT until “Hold to
Set” stops blinking.
4. Press MODE/NEXT until ”Calib.” appears.
5. Press START/LAP and circle the track on the
inside lane at a comfortable pace.
6. Press STOP when you pass the 400 meter
mark. The SDM Triax 100 will calculate the
distance that you have traveled.
7. If this does not equal the actual distance
you ran, use the START/LAP and STOP
buttons to adjust the distance display so
that it matches the distance you traveled.
8. Press MODE/NEXT to complete setup. Your
speed and distance will be automatically
calculated using the new calibration.
Or, press ADJUST/EXIT to return to the
original factory calibration.
BATTERY CHANGE
To replace the batteries, remove the two
battery cover screws on the speed sensor clip.
Pull off the battery cover and replace with 2
AAA batteries. Make sure the batteries are
correctly aligned. Then replace the battery
cover and battery cover screws.
Low battery power is indicated by a
rapidly flashing LED.
CALIBRATION
T
X
E
N
/
E
D
O
M
S
T
O
P
S
T
A
R
T
/
L
A
P
T
I
X
E
/
T
S
U
J
D
A
S
T
A
R
T
/L
A
P
A
D
JU
S
T
/ E XIT
M
O
D
E
/
N
E
X
T
ST
O P
H20 RESIST 1
00M
ADJUSTING THE DISPLAY
If necessary, you can calibrate
your watch by running a
known distance and adjusting
the display accordingly.
S
T A
R
T
/L
A
P
A
D
JU
S
T
/ E XIT
M
O
D
E
/
N
E
X
T
ST O
P
H20
R ESIS
T 1
00M
BATTERY CHANGE
Remove the two battery
screws to access the batteries.
9328.2- SDM-ENG 6/13/00 5:51 PM Page 8