P:\INSTALLATION INST\Access Controls\INST-920\INST-920.vsd Rev C 10-14 Page 2
CAUTION
IF THE UNIT IS AC POWERED, MAKE SURE
THAT THE SECONDARY OF THE SYSTEM IS
ISOLATED FROM EARTH GROUND
!
!
Fig. 2 Wiring Pigtail Color Code
KEYPAD
POWER
WIRE
HARNESS
(E1-E8)
MAIN
RELAY
AUXILIARY
RELAY
ANTI-TAMPER
SWITCH
BACK
JP1
E1
E8
JP2
TO POWER SUPPLY
KEY PAD POWER
12-24 VOLTS
AC OR DC
}
+
-
RED
BLACK
NC
AUXILIARY RELAY
2 AMPS @ 28VDC MAX
}
NO
COM
ORG/BLK
BLK/WHT
BRN/YEL
MAIN RELAY
5 AMPS @ 28VDC MAX
}
NO
COM
NC
ORANGE
WHITE
YELLOW
BLACK
PINK/SALMON
GREEN
GRAY
BLACK
VIOLET
BLACK
BLUE
DOOR POSITION
SWITCH
[N/C]
REQUEST-TO-EXIT
SWITCH
[N/O]
GROUND
OUTPUT #4
OUTPUT #3
GROUND
GROUND
SENSE
REQUEST TO EXIT
GROUND
EARTH
GROUND
CONNECTION
E
1
E
8
E
7
E
6
E
5
E
4
E
3
E
2
C
NO
C
NC
NO
AUXILIARY OUTPUTS
100mA MAX TO COMMON
{
*
*
QuickStart Programming
You must first enter programming mode to perform any function. The yellow indicator will blink slowly showing that the 920
EntryCheck™ is in programming mode. Use the option codes to program each function. After the new data entry is complete for
each function , the yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the
programming has been accepted. The red indicator will light if any programming data is entered incorrectly or the function is
rejected. If a red indicator is seen, the entire function (option code + data) will have to be fully re-entered. The keypad will remain
in programming mode until # is pressed or after 30 seconds of inactivity.
**
RED/GREEN
POWER/ACCESS
INDICATOR
YELLOW
“PROGRAM”
INDICATOR
KEYPAD
FRONT
Test your new user code
Enter user code ‘9876#’. The green indicator should illuminate, the
main relay should activate and the door should unlock for 5 seconds.
Program the first user code
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
03# 4#
Set the entry code length to 4 digits
Step 3. Enter:
21# 5#
Set the main relay activate time to 5 sec.
Step 4. Enter:
01# 001# 9876# 9876# 1#
PIN code ‘9876’ is assigned to User #001 to
momentarily activate the main relay
Step 5. Enter:
#
Exit programming mode
**
Adding additional user codes
Once the code length and relay time have been set you do not need to set them each time
you additional users.
To add additional users:
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
01# 002# 2222# 2222# 1#
PIN code ‘2222’ is assigned to User #002 to
momentarily activate the main relay
Step 3. Enter:
01# 003# 2580# 2580# 10#
PIN code ‘2580’ is assigned to User #003 to
toggle (on/off) the main relay
Step 4. Enter:
#
Exit programming mode
**
Deleting a user code
To delete a user:
Step 1. Enter:
#9# 123456#
Enter the program mode (default master code)
Step 2. Enter:
02# 002# 002#
User #002 has been deleted.
Step . Enter:
#
Exit programming mode
**
