background image

Page 16 -  Galaxy 2000RS Plus

or in severe temperatures, in which case the tach wire must be connected.  

Tach Monitor. Monitors the vehicle’s tach wire (or a fuel injection wire) in real-time to determine engine
status and adjust starter crank time automatically.  If programmed for Tach Monitor, the vehicle’s tach
signal will have to be learned before initial operation (see below).

15.

Remote  Start  Program

.    This  dual  program  branch  sets  the  engine  mode  for  Gas  or  Diesel,  and

learns the vehicle’s RPM threshold.  For installation into a diesel equipped vehicle, first set the engine
type to diesel before learning RPM.

RPM Learn. After engine type is set, start the engine, re-enter Branch 15, LED will start flashing if tach
signal is detected, otherwise the LED will stay solid. Press Button 1 to learn the vehicle’s idle speed.
The siren will chirp once to confirm. The siren will chirp four times if the tach signal was not learned.

Gas Engine. Sets the engine type for Gasoline.  

Diesel Engine. Sets the engine type for Diesel and monitors the glow plug input to make sure the glow
plugs are warm before cranking the starter.  If the glow plug wire is not connected, the built-in timer
waits 15 seconds before automatically cranking the starter.

16.

FM Transmitter Program

.*  Programs the optional FM module and transmitter into the system.  

FM Module Learn. Learns the add-on FM module ID so the FM transmitter can operate the system. The
FM module must be connected before completing this step. 

FM Remote Learn. Learns the optional 2-way FM transmitter.  Press Button 2 on the 1-way remote to
enter FM Transmitter learn mode, then press transmitter Button 1 on each FM remote (max 2).

*Requires the optional ScyNet FM LCD Pager Module.

17.

Ignition  2  Relay  Program. 

Selects  one  of  three  operating  modes  for  the  Ignition  2  relay  output:

Ignition 2, Accessory 2, or Starter 2. 

18.

Horn Output. 

When set for Horn Output the horn wire will pulse when the alarm is triggered.  When

Ignition 3 Output is selected, the output will activate during remote start to trigger a relay for Ignition 3. 

19.

Turbo Timer. 

When enabled, if the emergency brake has been applied Ignition power will be kept On

for a predetermined time (2min. Factory Default) from the application of the emergency brake.

Содержание Galaxy 2000RS-MDL





























Отзывы: