Scout MT-700 ENT Скачать руководство пользователя страница 28

Страница: 28 / 155

МТ-700 fleet tracking system

Figure 21

It is forbidden

to make holes in the terminal enclosure.

It is forbidden

to mount the tracker on the vehic

le’s moving

mechanisms.

The terminal has an internal acceleration sensor, so mounting onto

non-stationary objects may lead to incorrect tracker performance(motion
and parking regimes, work regimes etc).



Sealing the tracker

It is recommended to seal the device after assembling it in the enclosure.
If the tracker is mounted without a connectors’ lid, then it is recommended to seal the

connector (

Figure 22

). When sealing the connector make sure that unplugging it will cause a seal

violation.

Figure 22

If the connectors’ lid is installed, then sealing can be done in different ways:

Содержание MT-700 ENT




























































































































































Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды

Scout MT-700 ENT, Руководство по эксплуатации

Результаты поиска

Содержание MT-700 ENT

Отзывы:

Похожие инструкции для MT-700 ENT

Бренды по названию

Популярные бренды