manualshive.com logo in svg

Scotsman UF424A-1A, Техническое руководство

Поделиться
Скачать
Scotsman UF424A-1A Скачать руководство пользователя страница 29

UF424 / UN324 Technical Manual

September 2017

Page 29

Replace Auger Motor

Auger Motor

The auger motor may be replaced without removing 

the gear reducer. Due to manufacturing and testing 

reasons, the replacement auger drive motor is 

supplied mounted on a gear reducer cover. It is not 

necessary to replace the gear reducer cover. 

1.  Remove 3 screws holding motor cover to motor.
2.  Remove 4 screws holding rotation sensor to 

motor.

3.  Use a cordless impact driver to remove the 

screw holding the magnet rotor. If needed use 

the special thin 3/8 open end wrench to hold the 

motor shaft.

4.  Remove the original drive motor. 
5.  Separate the replacement drive motor from the 

shipping casting.

6.  Install the rotor of the replacement motor into the 

gear reducer.

7.  Attach the winding of the replacement motor to the 

gear reducer.

8.  Attach the magnet rotor to the new motor shaft.
9.  Attach the sensor and its holder to the motor.
10. Attach the motor cover to the motor. Reconnect 

wires.

Electrical Shock Hazard
Disconnect electrical 

power before beginning

Содержание UF424A-1A




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды