Scotsman TDE550 Скачать руководство пользователя страница 1

INTRODUCTION

To the owner or user: The service manual you are
reading is intended to provide you, and the
maintenance or service technician with the
information needed to install, start up, clean,
maintain, and service this ice maker-dispenser.

The TDE650 is a combination nugget ice maker
and countertop dispenser, with the option of wall
mounting.

The TDE650 ice making section is equipped with
the following features: electronic controls for bin
level and low water; thermostatic expansion valve;
front service for most components; and R-404A
(HP62) refrigerant. The ice dispensing section is a
seamless plastic storage bin, with a stainless steel
rotating vane to sweep the ice into the dispensing
chute.

Table of Contents

FOR THE INSTALLER: Specifications . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 2

FOR THE INSTALLER: Environmental Limitations . . .   . . .   . . .   . . .   . . .   .

Page 3

FOR THE INSTALLER: Wall Mount Kit

.   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 5

FOR THE PLUMBER

. .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 6

FOR THE ELECTRICIAN .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 7

FOR THE INSTALLER: Final Check List .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 8

INITIAL START UP

. . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 9

COMPONENT DESCRIPTION

.   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 10

COMPONENT DESCRIPTION: Control Box

. .   . . .   . . .   . . .   . . .   . . .   .

Page 12

ELECTRICAL SEQUENCE

. . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 13

OPERATION: Water

. .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 14

OPERATION: Refrigeration . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 15

OPERATION: Ice Vending

. . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 16

DISPENSE AREA SANITATION .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 17

CLEANING and SANITIZING

. .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 18

MAINTENANCE AND CLEANING

. . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 19

SERVICE DIAGNOSIS

.   . . .   . . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 21

SERVICE DIAGNOSIS: Circuit Board . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 23

REMOVAL AND REPLACEMENT

. . .   . . .   . . .   . . .   . . .   . . .   . . .   .

Page 24

REMOVAL AND REPLACEMENT: Bearing And Breaker

. . .   . . .   . . .   . . .   .

Page 25

REMOVAL AND REPLACEMENT: Water Seal

.   . . .   . . .   . . .   . . .   . . .   .

Page 27

TO REMOVE AND REPAIR THE GEARMOTOR ASSEMBLY

.   . . .   . . .   . . .   .

Page 29

REFRIGERATION SERVICE: R-404A (HP62)

.   . . .   . . .   . . .   . . .   . . .   .

Page 30

Parts Lists and Wiring Diagrams are printed on
yellow paper in the center of this manual.

This manual was printed on recycled paper.

Keep it for future reference.

Note this symbol when it appears.

It marks a possible hazard.

TDE550 & TDE650

November 1995

Page 1

Содержание TDE550

































Отзывы: