manualshive.com logo in svg

Scotsman NME1250R, Руководство по обслуживанию

Поделиться
Скачать
Scotsman NME1250R Скачать руководство пользователя страница 35

INSTRUCTIONS FOR USING TESTER
(Optional, order part no. A33942-001)
(These instructions assume that the unit will not run, and prior investigation of electric power, controls, and
mechanical parts indicates that the electronic circuit may be at fault.)
Bin Control  

Note: All testing is done with the

electrical power on, the master switch on, and  all
reset switches "reset" .
1. Unplug "photo trans" and "LED" connectors
from the circuit board.
2. Plug "photo trans" and "LED" connectors from
the tester into the circuit board.

a. Move the "bin full" switch on the tester to Full.

The light on the tester should be ON.
If the light on the tester is not on, the circuit board
should be replaced.

b.  If the light on the tester IS on, move the "bin

full" switch to Bin Empty.  The light on the tester
should go OFF, and the Bin Empty light on the
circuit board should go ON.
If  the machine still does not run, replace the ice
level sensors.

ELECTRONIC CONTROL TESTER 

PHOTO TRANS

LED

LIGHT

GOES ON

SWITCH TO

"FULL"

LIGHT GOES ON

SWITCH TO 

"BIN EMPTY"

LIGHT

GOES OFF

Electrical shock hazard.

Electrical power can
cause personal injury.
Disconnect electrical
power before beginning.

NME1250R

August  1993

Page 35

Содержание NME1250R





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды