Scotsman FME1504R Скачать руководство пользователя страница 29

Страница: 29 / 34

To Remove the Auger:

Turn off the water to the machine, and unclip the

evaporator drain hose, pull it down and drain the

evaporator into the bin or a container.

1. The top panel must be removed.

2. The auger and breaker/bearing may now be

removed as an assembly.

a. Unscrew 4 allen head cap screws holding

breaker to evaporator.

b. Lift up on breaker and remove auger from

evaporator.

Note: If the auger is stuck, the breaker must be

removed from the auger.

The breaker may be removed from the auger and

evaporator without disturbing the auger.

a. Unscrew breaker cover from breaker (left hand

threads)

b. Unscrew auger stud from top of auger.

c. Unscrew 4 allen head cap screws holding

breaker to evaporator.

d. Use a slide hammer type puller to pull on the

auger at the threaded hole. The size of that hole

is 5/8"-18.

Inspect the auger, the critical areas of the auger

are:

a. The auger body. It should be clean and

shining. Sometimes an auger will appear clean

when wet, but after it is dry it will be seen to be

stained. Scrub the auger with ice machine cleaner

and hot water.

Ice machine cleaner is an acid. Handle it with

extreme care, keep out of the reach of children.

b. The water seal area. Because the auger has

been removed, the water seal will have to be

replaced. Remove the water seal top half from the

auger, and inspect the auger for minerals clean as

required.

NME1254R & FME1504R

January 2000

Page 29

REMOVAL AND REPLACEMENT: Auger

SLIDE

HAMMER

PULLER

Hazardous Moving

Parts.

Moving auger can cause

personal injury.

Disconnect electrical

power before beginning.

ALLEN

SCREWS

BREAKER

ASSEMBLY

Содержание FME1504R



































Результаты поиска

Содержание FME1504R

Отзывы:

Бренды по названию

Популярные бренды

Scotsman FME1504R, Руководство по обслуживанию

Результаты поиска

Содержание FME1504R

Отзывы:

Бренды по названию

Популярные бренды