Scotsman FME1204R Скачать руководство пользователя страница 9

Страница: 9 / 34

FOR THE PLUMBER

CONFORM TO ALL APPLICABLE CODES

Water Inlet

Connect a cold potable water supply

to the ice machine. Use 3/8" O.D.

copper tubing and connect it to the

3/8" male flare at the back of the

cabinet.
Install a hand valve near the machine

to control the water supply.

Drains

The cabinet has a ¾" FPT drain.

connection. The drain is at the back of

the cabinet, the drain line is of the

gravity type, and 1/4 inch per foot fall

is an acceptable pitch for the drain

tubing. There should be a vent at the

highest point of the drain line, and the

ideal drain receptacle would be a

trapped and vented floor drain. Use

only ¾" rigid tubing.

Storage Bin:

Install a

separate

gravity drain to the ice storage bin.

Insulation of this drain line is

recommended.

NME954R & FME1204R

January 2000

Page 9

Floor Drain

Vent Bin Drain

3/4" FPT

Vent Ice

Maker

Drain, 3/4"

FPT

Water Inlet

3/8" Male Flare

Field Supplied

Water Filter

Hand Shut

Off Valve

Connect To

Cold Water

Содержание FME1204R



































Результаты поиска

Содержание FME1204R

Отзывы:

Бренды по названию

Популярные бренды

Scotsman FME1204R, Руководство по обслуживанию

Результаты поиска

Содержание FME1204R

Отзывы:

Бренды по названию

Популярные бренды