Scotsman FME1200 Скачать руководство пользователя страница 1

Страница: 1 / 32

INTRODUCTION

To the owner or user: The service manual you are
reading is intended to provide you, and the
maintenance or service technician, with the
information needed to install, start up, clean,
maintain, and service this ice system.
This machine is a modular ice system that fits a
variety of Scotsman ice storage bins.

It features: front service for the freezer, gear
motor, control box, water reservoir, and bin control;
an electronic circuit for monitoring ice and water
level; a thermostatic expansion valve; and R-404A
as the refrigerant.

This manual was printed on recycled paper.

Keep it for future reference.

TABLE OF CONTENTS

FOR THE INSTALLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2

SAMPLE BIN AND MACHINE COMBINATIONS . . . . . . . . . . . . . . . . . . . . . . Page 3

FOR THE INSTALLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4

FOR THE PLUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6

FOR THE ELECTRICIAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

START UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9

COMPONENT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10

COMPONENT DESCRIPTION: Control Box . . . . . . . . . . . . . . . . . . . . . . . . Page 11

ELECTRICAL SEQUENCE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13

OPERATION: Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 14

OPERATION: Refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15

OPERATION: Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15

SANITIZING AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16

MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17

MAINTENANCE: Air Cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18

MAINTENANCE AND CLEANING: Auger . . . . . . . . . . . . . . . . . . . . . . . . . Page 19

SERVICE DIAGNOSIS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20

REMOVAL AND REPLACEMENT: Water Reservoir & Bin Controls . . . . . . . . . . . . Page 22

REMOVAL AND REPLACEMENT: Bearing And Breaker . . . . . . . . . . . . . . . . . . Page 23

REMOVAL AND REPLACEMENT: Auger . . . . . . . . . . . . . . . . . . . . . . . . . Page 24

REMOVAL AND REPLACEMENT: Water Seal . . . . . . . . . . . . . . . . . . . . . . . Page 25

REMOVAL AND REPLACEMENT: Evaporator . . . . . . . . . . . . . . . . . . . . . . . Page 26

REMOVAL AND REPLACEMENT: Gearmotor . . . . . . . . . . . . . . . . . . . . . . . Page 27

REMOVAL AND REPLACEMENT: Fans . . . . . . . . . . . . . . . . . . . . . . . . . . Page 28

REFRIGERATION SYSTEM SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 29

LIQUID CHARGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 30

CIRCUIT BOARD TESTING: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 31

Parts lists and wiring diagrams are in the center of this manual, printed on yellow paper.

Note the warning symbol
where it appears. It marks a
possible hazard.

NME950 & FME1200

January 1995

Page 1

Содержание FME1200

































Результаты поиска

Содержание FME1200

Отзывы:

Похожие инструкции для FME1200

Бренды по названию

Популярные бренды

Scotsman FME1200, Руководство по обслуживанию

Результаты поиска

Содержание FME1200

Отзывы:

Похожие инструкции для FME1200

Бренды по названию

Популярные бренды