Scotsman ECC1200 Series страница 32 Скачать руководство пользователя

Страница: 32 / 57

EH330, EH430 and ECC Condensing Unit

Remote Low Side Cuber Service Manual

May 2015

Page 31

Ice Thickness and Water Purge Adjustment

Bridge Thickness - For the Service Tech Only

1. Push and hold Off till the machine stops.

2. Remove evaporator cover.

3. Remove curtain.

4. Use a hex wrench and rotate the bridge thickness

adjustment screw in 1/16 turn increments CW to

increase bridge thickness.

5. Rotate CCW to decrease bridge thickness.

Caution: Do not make the bridge too thin or the

machine will not harvest properly. Bridge thickness

adjustments are not covered by warranty.

6. Return curtain and evaporator cover to their

normal positions.

7. Push and release the On button. Check next

harvest of ice. Repeat steps 1-6 if needed.

Water Purge Setting

The water purge is factory set to the automatic

position, suitable for most water conditions. The

setting can be changed to one of 5 manual settings or

left on automatic.

Setting Water Type
1

Minimum - RO water or equivalent

Moderate - Low TDS, non RO

Standard - Use with typical water

Heavy - High TDS

Maximum - Very high TDS

Automatic - Factory setting

To set:

1. Switch the machine OFF by holding the Off button

in until a number or the letter A shows on the

display.

2. Press and release the On button repeatedly until

the number on the display corresponds to the

desired setting.

3. Press and release the Off switch again to return to

the normal control state.

1/8 to 3/16”

Bridge

Adjustment

Screw

Bridge Thickness Adjustment Mechanism

ice Bridge Thickness

Содержание ECC1200 Series


























































Результаты поиска

Содержание ECC1200 Series

Отзывы:

Похожие инструкции для ECC1200 Series

Бренды по названию

Популярные бренды

Scotsman ECC1200 Series, Руководство по обслуживанию

Результаты поиска

Содержание ECC1200 Series

Отзывы:

Похожие инструкции для ECC1200 Series

Бренды по названию

Популярные бренды