background image

CLEANING

How to clean the ice making system.

1. Open the door and
turn the ice machine
control knob to off.

2. Scoop out all of the ice, either discard it or save
it in a ice chest or cooler.

3. Pour 4 ounces of Scotsman Ice Machine
Cleaner (available from a local Scotsman
Distributor or Dealer, ask for part number
19-0343-06 - an 8 ounce bottle) into the ice
machine reservoir.

4. Turn the ice machine control to ON.

5. Allow the machine to operate for about 2 hours.

6. Pour hot (95

0

F. - 115

0

F.) water into the bin to

melt the ice that has formed. That ice will likely be
white and frosty looking.

7. Clean the bin liner of mineral scale by mixing
some ice machine cleaner and hot water, and
using that solution to scrub the scale off of the
liner.

8. Rinse the liner with hot water.

9. Sanitize the bin interior.

10. Replace the ice removed in step 2.

The ice scoop should be washed regularly, wash it
just like any other food container.

DCE33

September 2011

Page 17

Scotsman Ice Machine
Cleaner contains acids.

These compounds may
cause burns.

If swallowed, DO NOT
induce vomiting. Give
large amounts of water or
milk. Call Physician
immediately. In case of
skin contact, flush with
water. Keep out of the
reach of children.

Содержание DCE33 Series













































Отзывы: