background image

CSE60

November 2004

Page 14

1. Remove the ice from the bin.

2. Remove front panel.

3. Rotate control knob counter clockwise to the Off
position.

4. Turn off the water supply to the ice machine.

5. Remove top panel.

6. Remove plastic panel (evaporator cover) that
covers evaporator section.

7. Remove curtain by pulling forward on the left end,
and then pulling the curtain to the left and out of the
machine.

8. Lift up spray platform, locate stand pipe to the right
of the opening, and pull it out to drain the reservoir.
Return the standpipe, spray platform, and curtain to
their original positions.

9. Mix approximately 3 ounces (1/10 liter) of
Scotsman Ice Machine Cleaner with 1.5 quarts (1.5
liter) of warm (95-115

o

F.) potable water, and pour this

solution over the evaporator section (bright metal
tubing and inverted cups in white plastic tray at the
top of the ice machine).

10. Return the evaporator cover removed in step 6 to
its normal position.

11. Rotate the control knob to the Normal position.

12. Operate the machine with the cleaning toggle
switch in the Operation position for 5 minutes.

13. Switch the cleaning toggle switch to the Cleaning
position and operate the machine for 1 minute.

14. Repeat steps 12 and 13 three times. After the
third time rotate the control knob counter clockwise to
the Off position.

15. Remove evaporator cover. Pour hot water over
the entire surface of the evaporator section. Return
evaporator cover to its original position.

16. Pour hot water into the bin to melt any ice
produced during cleaning, and to clean out the drain.
Wipe the interior of the bin with mild soap and hot
water, rinse with cold water.

To sanitize, mix a locally approved sanitizer solution
and perform steps 17-31. A possible sanitizer solution
may be obtained by mixing 1 ounce of household
bleach with 2 gallons of

warm (95-115

o

F)

water.

17. Remove plastic panel (evaporator cover) that
covers evaporator section.

18. Remove curtain by pulling forward on the left end,
and then pulling the curtain to the left and out of the
machine.

19. Lift up spray platform, locate stand pipe to the
right of the opening, and pull it out to drain the
reservoir. Return the standpipe, spray platform, and
curtain to their original positions.

20. Pour sanitizer solution over the evaporator
section (bright metal tubing and inverted cups in white
plastic tray at the top of the ice machine).

21. Spray or wash the bottom of the evaporator cover
and the edges of the evaporator section with the
sanitizing solution.

22 Return the evaporator cover removed in step 17
to its normal position.

23. Rotate the control knob to the Normal position.

24. Operate the machine with the cleaning toggle
switch in the Operation position for 4 minutes.

25. Switch the cleaning toggle switch to the Cleaning
position and operate the machine for 1 minute.

26. Repeat steps 23 and 24 five times. After the fifth
time rotate the control knob counter clockwise to the
Off position.

27. Remove evaporator cover. Pour sanitizer solution
over the entire surface of the evaporator section and
wash or spray the evaporator cover bottom with
sanitizer. Return evaporator cover to its original
position.

28. Remove curtain, lift up spray platform, locate
stand pipe to the right of the opening, and pull it out to
drain the reservoir.

29. Thoroughly spray or wipe the interior of the ice
storage bin, bottom of the evaporator cover and all of
the spray platform with the sanitizing solution.

30. Completely immerse the curtain in the sanitizing
solution.

31. Return the standpipe, spray platform, evaporator
cover and curtain to their original positions.

32. Reconnect water supply.

33. Rotate control knob to its original position. Switch
the cleaning toggle switch to the Cleaning position for
two minutes and then switch it to the Operation
position. Operate the machine until one batch of ice
has been released into the bin. Pour warm water over
the ice to melt it.

34. Return the front panel to its original position and
secure with the original screws.

Scotsman Ice Machine
Cleaner contains acids.
These compounds may
cause burns. If
swallowed, DO NOT
induce vomiting. Give
large amounts of water
or milk. Call Physician
immediately. In case of
external contact, flush
with water. KEEP OUT
OF THE REACH OF
CHILDREN.

SANITIZING AND CLEANING: In Place Cleaning

Содержание CSE60



















Отзывы: