Scientific SMO1002 Скачать руководство пользователя страница 65

Страница: 65 / 102

L) Storage System

Showing as following picture, The SAVE/RECALL is the Storage System Function Button.

You can quickly save and recall up to 20 oscilloscope panel settings, 20 groups’ waveforms(SMO702,

SMO1002 only have 10 groups) in internal memory. There is a USB Host interface in the front panel of the

oscilloscope and you can save setup data, waveform data, waveform interface image, CSV file to a USB

flash drive furthest at a time. Setup data and waveform data can be recalled to the current oscilloscope or

the other same model oscilloscopes. Picture data and CSV file can’t be recalled to the oscilloscope, but it

can be opened on the correlative computer software.

■

Using SAVE/ RECALL Screen

The SAVE ALL screen is divided into functions based on Directories or Files. Directories shows option

button for New Folder, Del Folder, and Load.

While File shows option buttons for New File, Delete File, and Load.

Fig. 50 SAVE/ RECALL Menu Selection

Fig. 51 SAVE/ RECALL Screen A

User Manual SMO702, SMO1002

Содержание SMO1002







































































































Результаты поиска

Содержание SMO1002

Отзывы:

Scientific SMO1002, Руководство пользователя, Страница: 65 / 102

Результаты поиска

Содержание SMO1002

Отзывы: